0
What else can I help you with?
What has one hole and can hold glass tubing?
A rubber stopper with one hole can be used to securely hold glass tubing in place, creating a seal that prevents leaks or spills. The tubing can be inserted through the hole in the stopper, allowing for a tight fit that helps with fluid transfer or containment.
Is a rubber stopper a mineral?
No, a rubber stopper is not a mineral. Rubber is a synthetic or natural polymer made from organic compounds, primarily derived from the latex of rubber trees or synthesized from petrochemicals. Minerals, on the other hand, are naturally occurring inorganic substances with a defined chemical structure.
When magnesium reacts quickly with hydrochloric acis to produce hydrogen gas in a glass tube with a rubber stopper why would the rubber stopper burst of?
The reaction between magnesium and hydrochloric acid produces hydrogen gas, which builds up pressure inside the closed glass tube. If the pressure exceeds the strength of the rubber stopper, it will burst off to release the built-up pressure and prevent the glass tube from breaking due to the increased pressure.
What is the function of a rubber bung?
A rubber bung (also called rubber stopper) is used in the laboratories for test tubes, flasks (made of glass usually). Bungs also used by winery industry for the wine bottles. A bung must fill well as a stopper. The bungs are of many sizes. Rubber bung can have one or more hole(s) for plugging in tube depending on the specification of the procedures. In chemical laboratory, to prevent the liquid chemical leaks or escape the container, we need the rubber bung that fit tightly to the container's open, therefore, the dimension of the rubber bung is concerned. These are some of the sizes that are commonly seen in chemical laboratory
Why are the tubes sealed with rubber stopper rather than left open?
To avoid loss of substances.
I have a beautiful glass globe hummingbird feeder that has a rubber stopper. How can I stop the nectar from leaking out of the stopper?
If there is debris on the stopper it might be preventing a good seal. Try removing the rubber stopper and wipe it off to remove any debris that might be on it. Clean out the hole that the stopper goes into as well. This will help ensure a clean seal between the hole and the stopper. Put the stopper back into the hole, making sure it is a tight fit. If it still leaks you may need to buy a new stopper.
Which hole does the rubber stopper go in inside the carb of 1986 Honda fourtrax fourwheeler?
Just sso happens I tore into my carb today and the rubber stopper goes 2nd hole.... outside in .....towards the main jet
What is the device used to bore holes through cork or rubber stopper?
Plug Hole I Think :)
Where can you buy a rubber stopper?
You can buy an rubber stopper at widget-co.com. They are not that expansive ethier
What is the volume of rubber stopper?
The volume of a rubber stopper can vary depending on its size and shape. To find the volume of a rubber stopper, you can use the formula for the volume of a cylinder or sphere, depending on the shape of the stopper. Measure the dimensions of the stopper and plug them into the appropriate formula to calculate the volume.
Toyota Previa oil light on but full of oil?
Try changing the oil pressure switch. now, where is the oil pressure switch? on the dash next to the trip odometer switch is a rubber stopper or a hole that leads into the dash. push a pen into the hole(remove rubber stopper) and depress the button in there. this is to be done after every oil change.
Would a rubber stopper float in water?
i don't know... That's why I'm asking you. soo.. Does a rubber stopper float in water?
Is the density of rubber stopper is denser than the density of water?
No, the density of a rubber stopper is less than the density of water. Rubber has a lower density compared to water, so a rubber stopper would float on water.
What has one hole and can hold glass tubing?
A rubber stopper with one hole can be used to securely hold glass tubing in place, creating a seal that prevents leaks or spills. The tubing can be inserted through the hole in the stopper, allowing for a tight fit that helps with fluid transfer or containment.
When a rubber stopper has a mass of 8.46g was immersed in a graduated cylinder containing 25 ml of water the water rose to 30.9 ml Calculate the densityof the rubber stopper?
The volume of the stopper can be calculated by subtracting the initial volume of the water from the final volume. In this case, the volume of the rubber stopper would be 30.9 ml - 25 ml = 5.9 ml. Now, divide the mass of the rubber stopper (8.46 g) by its volume (5.9 ml) to find its density. Density = Mass/Volume, so the density of the rubber stopper would be 8.46g / 5.9ml = 1.43 g/ml.
What is the average life expectancy of a rubber stopper?
This is very variable and depends on: - type of rubber - temperature - pressure on the stopper - the liquid in contact - other conditions of use
Who invented a rubber stopper?
The modern rubber stopper was developed in the 19th century, with significant contributions from Charles Goodyear, who is known for his work on vulcanization of rubber in 1839. This process made rubber more durable and elastic, paving the way for its use in various applications, including stoppers. While Goodyear didn't invent the rubber stopper itself, his innovations in rubber technology were crucial for its development.
