0
What else can I help you with?
How do you produce 230 volt by thermocouple action?
To produce 230 volts using thermocouple action, you would need to connect multiple thermocouples in series to add up their voltages. Each individual thermocouple generates a small voltage, typically in the range of millivolts, so by connecting them in series you can sum up their voltages to achieve the desired 230 volts. Keep in mind that the number of thermocouples needed would depend on the voltage output of each thermocouple and the overall design of the setup.
On the 20 volt range meter show 0.96 does this mean ninety six hunderdth's of a volt?
Yes. On the Scale, 20.00 would be 20 Volts and 01.28 would be 1.28 Volts.Therefore, 0.96 would equal 0.96 V or 960 mV
When testing for electrolysis in the cooling system the digital volt-ohmmeter (DVOM) reading should not exceed?
Go
What is the ac voltage reading between the bare copper wire and the hot black wire 120 vac or zero volt?
Should be about 120 VAC.
Why is it that the outlet shows 209 volts instead of 120 volts?
Because it is a 220 volt outlet instead of a 120 volt outlet. Now, if this is a standard 120 volt outlet that is reading 209 volts then someone has made a mistake in the wiring. You need to call an electrician to straighten this out.
Why thermocouple voltmeter is connected across shunt resistance and electronic voltmeter across capacitor?
There is no such a thing as a thermocouple volt meter. A analogue or digital millivolt meter or volt meter is connected across a shunt or parallel with the shunt to measure the current through the resistor. Say the resistor value = 1 Ohm, then by using the Ohm law formula to calculate the current, say the voltage (voltage drop), read on the volt meter is 1.5 Volt that is R*V = A that is, 1Ω*1.5V = 1.5 Amp. Any type of DC volt meter, analogue or digital can be used to measure the voltage across a capacitor if the value of the capacitor is large enough that reading will be true RMS. as long as the supply current (EMF Power) are larger than the load current.
What is a good voltage reading for a 12 volt battery?
For lead-acid chemistry, as in a car battery, think 13.6 volts DC.
How do you produce 230 volt by thermocouple action?
To produce 230 volts using thermocouple action, you would need to connect multiple thermocouples in series to add up their voltages. Each individual thermocouple generates a small voltage, typically in the range of millivolts, so by connecting them in series you can sum up their voltages to achieve the desired 230 volts. Keep in mind that the number of thermocouples needed would depend on the voltage output of each thermocouple and the overall design of the setup.
On the 20 volt range meter show 0.96 does this mean ninety six hunderdth's of a volt?
Yes. On the Scale, 20.00 would be 20 Volts and 01.28 would be 1.28 Volts.Therefore, 0.96 would equal 0.96 V or 960 mV
Use volt meter to check 12 volt battery charge level?
With your volt meter, touch the positive battery with the red wire and black to ground (neg, ) on the battery. With the engine off you should have a reading of anywhere from 12.2 to 12.6 volts. That is good. With the engine running at high rev's you should have a reading of any where from 14 to 14.5. When you charge the battery with a 2 amp charger it will take several days and the charge level will go up to 14.5 or so volts.
When testing for electrolysis in the cooling system the digital volt-ohmmeter (DVOM) reading should not exceed?
Go
How do you read 208 volts single phace circuit?
All voltage reading are usually read with a volt meter. This volt meter can be a hand held unit like electricians use.
What kind of battery does a kraken AK47 have?
A nickel caddmium (Ni-Cd) battery. It's an 8.4 volt 1500 mill amps per hour (maH)
If you have 123 volt at the plug what does this mean?
If you have 123 volt at the plug, this means that the voltage is a little high, or that the reading could have been taken at night when the system load was low. It is still safe to connect your appliances to it.
Can you use a 10 volt power supply for a 9 volt keyboard?
Using a 10 volt power supply for a 9 volt keyboard is not a good idea. The higher voltage will cause damage to the keyboard, burning it out and making it useless.
How do you chech the stator on a 1991 FLHTC When I unplug the regulator from the stator I should be able to take a volt meter and with the engine running get a volt reading from the stator. Right?
Yes, AC voltage.The regulator makes it DC.
What is wrong when your volt meter is maxed out on your 1986 dodge omni?
put a volt meter on the battery and check reading and see if it matches the metere in the car if over 15.0 volts, alternator is likely over charging
