0
The potential danger of using adapter plugs is that the user does not connect the ground wire as instructed to and this leaves the device connected into it unable to trip the breaker if a certain type of ground fault occurs on the device. Most adapter plugs have a ground wire that is supposed to be terminated under the face plate holding screw. This keeps the ground continues as the frame of the receptacle is grounded to the ground terminal in the junction box and the face plate screw uses the receptacle frame as its anchor point.
What else can I help you with?
Is it ok to leave an ac adapter plugged in?
It really is not safe to leave a AC adapter plugged in. If not using I would unplug it.
Can a 12 volt 0.5 amp ac adapter substituted with a 7.5 volt 1 amp adapter?
No, it is not recommended to substitute a 12 volt 0.5 amp AC adapter with a 7.5 volt 1 amp adapter. The voltage and amperage ratings need to match the requirements of the device you are powering. Using a lower voltage adapter may not provide enough power, and using a higher voltage adapter can potentially damage the device.
Can you use a 12v halogen bulb with a 6v AC adapter - wattage is the same?
No, you cannot use a 12v halogen bulb with a 6v AC adapter. The voltage of the bulb must match the voltage of the adapter for them to work properly. Using a higher voltage bulb with a lower voltage adapter can cause the bulb to burn out or potentially damage the adapter.
Can you use a 13v 2.77 amp ac adapter in place of a 12v 3.0 amp ac adapter?
It is not recommended to use a higher voltage adapter than what is specified for your device. Using a 13V adapter instead of a 12V adapter may damage your device due to overvoltage. It is best to use the adapter with the exact voltage and current specifications that are recommended by the manufacturer.
What if I Used wrong ac adapter in electronic device?
If the AC adapter gives too little voltage, the electronic device will probably not work. If it gives too high a voltage, you will probably burn out the electronic device, which will have to be replaced or rewired. If the AC adapter is too weak (provides less milli-amperes than the device needs), the AC adapter can burn out. In summary, you need to check: (a) that the adapter should have the correct voltage, and (b) that it provides the required amount of milliamperes (or more) for the device.
What is the proper procedure for using hand held visual distress signal flares?
Display only when immediate or potential danger exists
What are the benefits of using a bidet adapter in a bathroom?
Using a bidet adapter in a bathroom can provide benefits such as improved cleanliness, reduced toilet paper usage, and potential relief for certain health conditions.
What is this adapter for what does it do I found it while emptying a drawer and cant ever remember using it. http postimg org gallery 1wnuan2lk?
It's a type of ethernet adapter. But not sure as to what. Try to find out what type of cord plugs into the other end of the adapter.
What is the proper procedure for using hand-held distress signal flares?
Display only when immediate or potential danger exists
What is the proper procedure for using handheld visual distress signal flare?
display only when immediate or potential danger exists
What is the proper procedure for using hand-held visual distress signals?
display only when immediate or potential danger exists
What is the potential danger of using ties that pass circumerentially around the patients neck when securing an advanced airway?
Danger of asphyxiation (being choked) by the ties.
What is a potential danger of using SPAM filters?
Spam filters wont fully protect you from virus spams.
What is the potential danger and irony of using the device in Fahrenheit 451?
It would be dangerous and ironic to burn a book you were reading.
What is the proper procedure for using visual distress signal flares?
display only when immediate or potential danger exists
What are the benefits of using a GFCI outlet adapter for electrical safety in your home?
A GFCI outlet adapter can help prevent electrical shocks by quickly cutting off power if it detects a fault, protecting you and your family from potential harm.
What is proper procedure for using handheld visual distress signal flares?
display only when immediate or potential danger exists
