0
What is the problem when you add 2 additional outlets to an existing circuit and they show 60 volts no breaker trips?
First understand, a circuit breaker doesn't trip on low (60) voltage. It trips on overcurrent, or too many amps being drawn by the circuit.
A 60 volt reading in a 120 volt circuit is a typical "backfeeding" reading. You have something miswired. You may have tied into another circuit on the same phase. Go back and disconnect the feed to your 2 additional outlets. Check voltage on the last outlet on the original circuit. If you've got 120 volt, turn the circuit off, then wire in the first new outlet. Do not tie into any other wires other than the wire you ran from the last outlet in the original circuit. Turn the circuit back on and check voltage. You should have 110-120 volt. Then add the second additional outlet as per the above. Do not tie the neutral into any other wire than the one from the original circuit. This should clear your low voltage problem.
What else can I help you with?
If a 1950 era house has 10 gauge wiring for lights and outlets can you safely extend wiring with 12-2 for additional lights and outlets?
Mixing different gauge wires in the same circuit is not recommended as it can lead to electrical hazards. It is better to use the same gauge wire throughout the circuit to maintain consistency in the electrical load. If you're adding new lights and outlets, it's best to use the same gauge wire as the existing one.
What are the parts of the common household circuit?
A common household circuit consists of a breaker, wiring, outlets, and switches. The breaker protects the circuit from overloading, the wiring carries the electricity to the outlets and switches, and the outlets provide the connection for devices to receive power. The switches control the flow of electricity to the outlets or lights.
How many outlets and lights on a 60 amp breaker?
120 amps The above answer is wrong. A 60 amp breaker is designed to trip at 60 amps be it a single pole, double pole or a triple pole that is used on three phase equipment. The number on the handle of a breaker is the trip capacity.
Can wall outlets be on a 15amp breaker in the bedroom or do they have to be 20amp?
Technically, they can be on a 15 amp breaker when you use 15 amp outlets. There is a difference. Be sure to check your local code (just call the city building department and tell them you have a code question). some cities require the bedroom outlets to be on an arc-fault breaker.
What Voltage type are in outlets at home?
Your home electrical wall outlets current capacity is governed by the breaker that feeds that circuit. In most home situations the wall receptacles are fed with a 15 amp breaker. Dedicated outlets could have a higher ampacity as they are installed for specific appliances or devices. To check your circuit, plug a lamp into the outlet. Start flipping the breakers off. When the lamp goes out that is the breaker for that circuit. Look on the handle of the breaker and it will tell you the capacity of that particular circuit.
Are the lights and outlets in this room connected to the same circuit?
To determine if the lights and outlets in a room are connected to the same circuit, you can check the circuit breaker panel. If the lights and outlets are on the same circuit, flipping the breaker for that circuit will turn off both the lights and outlets. If they are on separate circuits, turning off the breaker for the lights will only affect the lights, and the outlets will still have power.
What size circuit breaker do you need for kichen counter outlets?
Two 20 Amp circuits with the outlets staggered so a different circuit is on two adjacent outlets. Should be GFCI protected.
If a 1950 era house has 10 gauge wiring for lights and outlets can you safely extend wiring with 12-2 for additional lights and outlets?
Mixing different gauge wires in the same circuit is not recommended as it can lead to electrical hazards. It is better to use the same gauge wire throughout the circuit to maintain consistency in the electrical load. If you're adding new lights and outlets, it's best to use the same gauge wire as the existing one.
When does a spur become necessary in electrical installation?
A spur becomes necessary in electrical installation when additional power outlets are needed beyond the existing circuit capacity. It is typically used to extend an existing circuit to provide power to appliances or devices in locations that lack sufficient outlets. A spur must be properly fused to ensure safety and comply with electrical regulations, and it should not exceed the load capacity of the existing circuit.
How can I wire multiple outlets and lights on the same circuit?
To wire multiple outlets and lights on the same circuit, you can connect them in parallel using a junction box. Run a main wire from the circuit breaker to the first outlet, then connect additional outlets and lights in parallel to the first one. Make sure to follow local electrical codes and use proper wiring techniques to ensure safety.
How can I wire outlets and lights on the same circuit?
To wire outlets and lights on the same circuit, you can connect them to the same electrical circuit breaker. Run the wiring from the breaker to the outlets and lights, making sure to follow proper electrical codes and safety precautions. Use separate wires for the outlets and lights, and connect them to the appropriate terminals on the outlets and light fixtures. It is recommended to consult a licensed electrician for guidance and to ensure the wiring is done correctly and safely.
What are the parts of the common household circuit?
A common household circuit consists of a breaker, wiring, outlets, and switches. The breaker protects the circuit from overloading, the wiring carries the electricity to the outlets and switches, and the outlets provide the connection for devices to receive power. The switches control the flow of electricity to the outlets or lights.
Why do outlets stop working?
Outlets can stop working due to issues such as a tripped circuit breaker, a blown fuse, a faulty outlet, or wiring problems.
Why are the outlets not working after a power outage?
After a power outage, outlets may not work due to a tripped circuit breaker or a blown fuse. This can happen when the sudden loss of power causes a surge when it comes back on. Resetting the circuit breaker or replacing the fuse can often fix the issue.
Why do my outlets not work and how can I fix them?
There could be several reasons why your outlets are not working, such as a tripped circuit breaker, a blown fuse, a faulty outlet, or a wiring issue. To fix them, you can try resetting the circuit breaker, replacing the fuse, checking and replacing the outlet if needed, or calling a professional electrician for help.
Is a ground fault indicator outlet installed at the breaker box?
There are tow places to put a Ground Fault Circuit Interrupter. There is a GFCI breaker which would be installed in a breaker box and a GFCI outlet that can be installed anywhere. Most GFCI outlets allow you to connect regular outlets to the GFCI and those outlets will also be protected.
What are the key features of the Klein ET300 digital circuit breaker finder?
The Klein ET300 digital circuit breaker finder features include the ability to quickly and accurately locate the correct circuit breaker in a panel, a digital display for easy reading, and a transmitter that plugs into outlets for tracing circuits.
