answersLogoWhite

0

Oh, dude, the size of a natural gas orifice for 50,000 Btu is typically around 0.052 inches. But hey, who's measuring, right? Just make sure it's not too big or too small, like finding the Goldilocks of orifices.

User Avatar

DudeBot

6mo ago

What else can I help you with?

Continue Learning about Natural Sciences

What is the size of a natural gas orifice?

The size of a natural gas orifice is typically measured in inches and can vary depending on the specific application and type of equipment. Common sizes range from 0.012 to 0.125 inches. It is important to use the correct orifice size to ensure proper gas flow and combustion.


What size orifice do you need for a Miller Nor-dyne 62000 BTU natural gas furnace?

For a Miller Nor-dyne 62000 BTU natural gas furnace, the orifice size typically needed is 0.125 inches (or 1/8 inch). However, it's essential to verify this with the manufacturer's specifications or installation manual, as orifice sizes can vary based on specific models and gas pressures. Always consult the furnace's documentation or a qualified technician for accurate guidance.


What drill size is the hole in a propane orifice for a gas space heater?

Depends on what the stove fires at.40 btu


What size orifice drill is needed for a natural gas burner using 5000 btus?

To determine the appropriate size orifice drill for a natural gas burner using 5,000 BTUs, you typically need to consider the gas pressure and the burner design. A common rule of thumb is that for natural gas, approximately 1,000 BTUs requires a drill size of about 0.025 inches. Therefore, for a 5,000 BTU burner, an orifice size of approximately 0.065 inches might be appropriate, but it's essential to consult manufacturer specifications or a gas sizing chart for precise requirements.


Where is the best place to get a Natural gas orifice for the change over from propane to natural gas on an Empire 65000 BTU floor furnace?

A supply house such as johnstone. Take all information of the furnace and old orifice with you and show them what you need.

Related Questions

What is the size of a natural gas orifice?

The size of a natural gas orifice is typically measured in inches and can vary depending on the specific application and type of equipment. Common sizes range from 0.012 to 0.125 inches. It is important to use the correct orifice size to ensure proper gas flow and combustion.


What size orifice do you need for a Miller Nor-dyne 62000 BTU natural gas furnace?

For a Miller Nor-dyne 62000 BTU natural gas furnace, the orifice size typically needed is 0.125 inches (or 1/8 inch). However, it's essential to verify this with the manufacturer's specifications or installation manual, as orifice sizes can vary based on specific models and gas pressures. Always consult the furnace's documentation or a qualified technician for accurate guidance.


What size drill bit is needed to drill a propane orifice to produce 15000 btu 11 WC?

54


What drill size is the hole in a propane orifice for a gas space heater?

Depends on what the stove fires at.40 btu


Where is the best place to get a Natural gas orifice for the change over from propane to natural gas on an Empire 65000 BTU floor furnace?

A supply house such as johnstone. Take all information of the furnace and old orifice with you and show them what you need.


Can you use natural gas in a propane orifice?

No, natural gas and propane orifices are not interchangeable. Natural gas orifices are larger than propane orifices due to the different properties of the gases. Using a propane orifice with natural gas can lead to incomplete combustion and potential safety hazards.


For equal Btu what is ratio for LP and Natural Gas orifice sizes?

Assuming the following typical conditions:natural gas manifold pressure is 3.5" w.c.propane manifold pressure is 10" w.c.natural gas and propane specific gravities are 0.6 and 1.52 relative to airnatural gas and propane energies per cubic foot are 1038 and 2516 BTUyour orifice coefficients are the samethen the propane orifice diameter should be 0.623 times the natural gas orifice diameter.


To go from natural gas to propane?

btu of natural gas to btu of propane


How many btu does a whole house generator use?

The BTU usage depends on the size generator. What you need to know to figure this out is the fuel type (propane or natural gas) and the size of the generator (usually measured in kilowatts or KW) and the size of the engine. Once you know these things, you can calculate the BTU. The easiest way is to ask the sales person or manufacturer. They can tell you the BTU.


What is the drill bit that i need to convert natural gas to propane at 40000 btu's?

you cannot do this because a natural gas orifice is larger than a propane orifice. you can make a propane jet work for a natural gas jet simply by drilling it approx. 210 % you must buy new jets. usually the company that made you appliance will sell the jet kits for you! HOPE THIS HELPS YOU! GOOD LUCK.


Natural gas Cubic feet to BTu?

102,000 BTU = 1 ccf


What size BTU natural gas heater should you buy for a 30'x50'x24' work shop?

Typically, use 5 * the volume in cubic feet to get BTU/hour for natural gas heaters. For this shop, that works out to 180,000 BTU/hr. Lower ceilings would make a big difference here...