0
What else can I help you with?
What size orifice do you need for a 28000 BTU propane heater?
I have a 40,000 btu forced air propane heater and its orfice is .085. I ended up drilling it out to 1/16", removing the regulator and hooking it up to NATURAL gas and it works fine. [for added info not pertaining to original question]
What should the orfice hole size be for lp gas?
The orifice hole size for LP gas is typically between 0.70-0.75 millimeters. However, it is recommended to consult the manufacturer's guidelines or a professional to ensure the correct size for your specific gas appliance. Improper sizing can lead to inefficient combustion and potential safety hazards.
What drill size is the hole in a propane orifice for a gas space heater?
Depends on what the stove fires at.40 btu
How do you convert a natural gas water heater to propane?
Usually gas appliances come with an extra valve in with the instructions. Just replace the valve. You may have to ask a heating specialist how to find the connection on your gas line. But it is not too difficult.
What size of breaker to use on a wall unit 220 heater?
The size of the breaker needed for a 220V wall heater depends on the current rating of the heater. Generally, for a 220V heater, a 20-amp breaker is common. However, it's important to check the manufacturer's specifications and local electrical codes for the appropriate breaker size.
What size orifice do you need for a 28000 BTU propane heater?
I have a 40,000 btu forced air propane heater and its orfice is .085. I ended up drilling it out to 1/16", removing the regulator and hooking it up to NATURAL gas and it works fine. [for added info not pertaining to original question]
What is the orfice hole size on a natural gas stove burner?
The orifice hole size on a natural gas stove burner typically ranges from 0.028 to 0.120 inches in diameter, depending on the burner size and design. Smaller burners generally have smaller orifice sizes, while larger ones require larger orifices to accommodate higher gas flow. It's important to check the manufacturer's specifications for accurate measurements, as specific requirements can vary by model.
What is the orfice size for propane power burners for kilns.....pottery.....and the like...?
what is the orfice sie for gas gill
What should the orfice hole size be for lp gas?
The orifice hole size for LP gas is typically between 0.70-0.75 millimeters. However, it is recommended to consult the manufacturer's guidelines or a professional to ensure the correct size for your specific gas appliance. Improper sizing can lead to inefficient combustion and potential safety hazards.
How do you convert a natural gas space heater to propane?
Converting a natural gas space heater to propane involves replacing the gas orifices, adjusting the air-to-fuel ratio, and installing a regulator designed for propane. It is important to follow the manufacturer's guidelines and have a professional technician perform the conversion to ensure proper and safe operation of the heater.
Natural gas to propane conversion?
you will need to buy a different size( orafise ) this is a small brass like nut with a small hole drilled thru it. the size of the hole is a different between propane and natural gas .
What drill size is the hole in a propane orifice for a gas space heater?
Depends on what the stove fires at.40 btu
Where is the block heater on 2003 Toyota Celica gt?
I was just looking over the shoulders of three befuddled mechanics trying to fit a block heater on my 2000 Toyota Celica. I'm still not sure if the heater is installed....I'm waiting, not too patiently. As for location, the heater is cylinder shaped and fits into a hole in the block on the right ( driver's side) of the motor. It appeared to be a dry hole ...not into the water cavity...just into the block. The hole is about centered, a little above the trans. All you would see is three prongs for the cord...or the cord. The hole is horizontal. It does not look like a typical block heater...just a cylinder about the size of a finger. Hope that helps. I was just looking over the shoulders of three befuddled mechanics trying to fit a block heater on my 2000 Toyota Celica GTS. I'm still not sure if the heater is installed....I'm waiting, not too patiently. As for location, the heater is cylinder shaped and fits into a hole in the block on the right ( driver's side) of the motor. It appeared to be a dry hole ...not into the water cavity...just into the block. The hole is about centered, a little above the trans. All you would see is three prongs for the cord...or the cord. The hole is horizontal. It does not look like a typical block heater...just a cylinder about the size of a finger. Hope that helps.
What is the hole in the mountain?
The hole in the mountain is known as a natural cave or tunnel formed by natural geological processes like erosion or volcanic activity. These openings can vary in size and shape and are often popular attractions for hikers and adventurers.
What size hole for swifts?
Swifts typically require a hole size of about 2.5 to 3 inches in diameter for nesting. This size allows them to enter and exit easily while providing a secure space for their nests. It's important to position the hole high up and in a sheltered location to mimic their natural nesting environments.
What is the appropriate water heater breaker size according to the water heater breaker size chart?
The appropriate water heater breaker size is determined by the water heater's wattage and voltage, as indicated in the water heater breaker size chart. It is important to match the breaker size to the specifications of the water heater to ensure safe and efficient operation.
What size space heater would fit in a living room or bedroom?
The size of a space heater depends on the size of a living room or bedroom. The best size for a space heater is 150 sq. ft for living rooms and bedrooms.
