answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

What size of breaker to use on a wall unit 220 heater?

The size of the breaker needed for a 220V wall heater depends on the current rating of the heater. Generally, for a 220V heater, a 20-amp breaker is common. However, it's important to check the manufacturer's specifications and local electrical codes for the appropriate breaker size.


If your wall receptacle has tripped but not at the circuit breaker how can this problem be repaired?

If the wall receptacle has tripped but not at the circuit breaker, it could be a faulty GFCI outlet. Try pushing the reset button on the GFCI outlet itself to restore power. If that doesn't work, you may need to replace the GFCI outlet. Make sure to turn off the power at the breaker before attempting any repairs.


Is 30 amp double pole breaker ok for 4800 watt wall heater?

Yes, a 30 amp double pole breaker would be suitable for a 4800 watt wall heater. Since watts equals volts multiplied by amps, this wall heater on a 240-volt circuit would draw 20 amps (4800 watts/240 volts), which is less than the 30 amp capacity of the breaker.


What wire size should you use with a 30 amp breaker?

No! The minimum wire size allowable is 10 gauge for a 30 amp circuit. Don't risk the chance of an inner wall fire because too small of a wire gauge was used. Never shortcut anything to do with electrical wiring. Never.


Can wall outlets be on a 15amp breaker in the bedroom or do they have to be 20amp?

Technically, they can be on a 15 amp breaker when you use 15 amp outlets. There is a difference. Be sure to check your local code (just call the city building department and tell them you have a code question). some cities require the bedroom outlets to be on an arc-fault breaker.

Related Questions

What size of breaker to use on a wall unit 220 heater?

The size of the breaker needed for a 220V wall heater depends on the current rating of the heater. Generally, for a 220V heater, a 20-amp breaker is common. However, it's important to check the manufacturer's specifications and local electrical codes for the appropriate breaker size.


What best breaker rating for 1.5 hp air-con unit?

The breaker you use is determined by the size of the wire in the wall not by what is being connected to that circuit. If you have 14/2 wire then use a 15 amp breaker. If you have 12/2 wire then use a 20 amp breaker. The breaker protects the wiring not the item connected.


What is tripping relay?

You need to remove everything connected to the breaker and see if it still trips. If it does it is in the wiring or possibly a bad breaker. Disconnect load from breaker and see if it still trips. If so replace the breaker. If it still trips and is not the breaker then you will have to start pulling each outlet from wall and checking after disconnecting each outlet.


Is wall breaker a fast twitch muscle?

yes it is


Where is the garage breaker box located in the house?

The garage breaker box is typically located on a wall inside the garage, near the main entrance or on the wall closest to the house.


How much wallpaper do I need for a wall that is 9ft by 15 ft has a door 3ft wide and 7 ft tall?

You need to know how long each wall is as well as how tall the room is. Also, you have specified the door size. Are there no windows?You need to know how long each wall is as well as how tall the room is. Also, you have specified the door size. Are there no windows?You need to know how long each wall is as well as how tall the room is. Also, you have specified the door size. Are there no windows?You need to know how long each wall is as well as how tall the room is. Also, you have specified the door size. Are there no windows?


Will turning off power to a ceiling fan via a wall switch be sufficient fro installing a new fan or must the circuit breaker be off too?

You need to turn off the power at the circuit breaker.


What size flat wall mount would I need to buy to hang this 52inch tv?

The size of wall mount you need is around 50 inch wall mount or higher. For the sake of being sure, you may need to ask a professional for assistance on the subject. Good Luck on finding your answer.


Can a 220 Volt well motor be added to a 200 amp box or does it need its own box?

The well pump breaker is installed in two slots in your breaker box. You then run the correct size cable for the amperage of the pump to the area where the pressure tank is located. install a breaker or disconnect on the wall near the pressure tank and then connect the low pressure switch to the disconnect. Connect the pump to the low pressure switch.


How can I reset a wall outlet?

To reset a wall outlet, locate the circuit breaker panel in your home and find the breaker that corresponds to the outlet. Turn the breaker off, wait a few seconds, and then turn it back on. This should reset the outlet and restore power to it.


What is the size and installation process for this air conditioner?

The weight is 128 lbs and is to be wall mounted, you will need a hole in the wall that fits it.


Can you install a main breaker box between studs on a outside wall?

Yes