0
What else can I help you with?
How many volts in a high tension wire?
The value of high voltage is based on level of a spark produced and the level of a shock given. The standard numerical range in the US is any voltage over 600 The value of high voltage is based on level of a spark produced and the level of a shock given. The standard numerical range in the US is any voltage over 600V.
What is a distribution voltage?
An intermediary voltage between high voltage and low voltage. I previously wrote 69kV and 34.5kV were distribution level voltages. This is not true, these are generally considered "sub Transmission" level. Anything below ~ 33kV and above ~1kV is considered distribution. Common voltages of this range I've seen are 2.4kV, 12.5kV, 13.8kV.
What was the threshold voltage in activity 1?
The threshold voltage in Activity 1 was the voltage required to trigger an action potential in the neuron, usually around -55mV. This voltage level is necessary to open voltage-gated sodium channels and initiate the depolarization phase of the action potential.
How does a series regulator maintain the output voltage at a constant level?
A series regulator maintains output voltage by adjusting its resistance to compensate for changes in input voltage or load current. It compares the output voltage to a reference voltage and regulates the voltage by adjusting the series pass device to ensure the output remains constant. This feedback loop continuously monitors and adjusts the output voltage, providing a stable output despite variations in input or load.
Why there is different types of voltage range 210 Volt 220 Volt 230 Volt 240 Volt 250 Volt in single phase AC system and what it based?
In the US the voltage is about 220 volts. This voltage is based upon the average voltage of the AC sine wave. It can peak as high as 240 volts or as low as 210 volts. So these different voltages are actually referring to an average 220 volt system.
What would likely be the primary distribution voltage used by an electric utility company?
The primary distribution voltage used by electric utility companies typically ranges from 4 kV to 34.5 kV. This voltage level is chosen to efficiently transmit electricity over medium distances while minimizing losses and ensuring safety. The exact voltage may vary based on regional standards, infrastructure, and specific utility practices.
How do you calculate the earth fault level of 4 MVA at 11K.V. power installation?
You need to know the expected voltage (what you have) and the system impedances (which you don't have). Voltage / impedance will give you the current (I assume this is the "fault level" you are looking for). If you request this from a utility, it may be good to ask them for a double check of your calculations as well.
Why a motor starts in star and runs in delta?
This configuration is used to reduce the starting current. Utility companies do not like large motor loads starting across the line. It dips the voltage level of the line. By reducing the starting current to a lower level also reduces the voltage dip in the supply lines.
Is utility constant along a demand curve?
utility is not constant along the demand curve
What is part worth utility?
In conjoint analysis, a part-worth utility refers to the utility of a certain attribute level.
Can you improve the voltage level without transformer?
yes, we can incease voltage level by aplifiers.......
What is the Formula to covert voltage level to decibel?
You mean the conversion from voltage V to voltage level LV. Voltage level LV = 20 * log V 117 volts equals 41.36 dB. The reference voltage 1 volt means 0 dB.
What instrument can detect the presence of voltage but not the voltage level?
a multimeter?
Why ttl voltage level converting to rs232 level?
Whwn an IC is connected to a PC, then the voltage levels of these two should be synchronized. For this purpose, the TTL voltage level is converted to RS 232 level. RS 232 is the interface between a PC and an IC.
What is the voltage level of laptop?
160
How can one determine demand from a utility function?
To determine demand from a utility function, one can use the concept of marginal utility. By calculating the change in utility for each additional unit of a good consumed, one can determine the level of demand for that good. The point at which the marginal utility equals the price of the good represents the optimal level of consumption and therefore the demand for that good.
When using Microsoft sync toy utility list the high level steps you would use to test the utility?
Doge
