answersLogoWhite

0

What else can I help you with?

Continue Learning about Natural Sciences

How do you separate a mixture that contains Iron fillings sand water and rubbing alcohol?

Here's my suggestion: Pour the full mixture through a filter paper. This will leave the water/alcohol mix in the bottom of the beaker and the iron/sand mix in the filter paper. To separate the iron and sand, I'd wait for the mix to dry and spread the mix out on a flat piece of paper. By using a magnet, you can pick out the iron filings- leaving the sand behind. The water/alcohol mix poses more problems! Hopefully, a layer will form between the two due to different densities etc. If so, one layer can be removed via a pipette. However, a more tedious method could be to... Set up a flask and sit it on a tripod and gauze. Put the mixture in the flask. GENTLY heat the flask with a Bunsen burner, with a distillation tube fitted to the flask ( also known as a reflux condenser). If the mixture isn't allowed to boil, the alcohol will evaporate away, go down the distillation vessel and into a clean beaker, leaving the water behind. Hope this is adequate?!


How will you separate a mixture of aluminium and iron filings and sugar?

To retrieve the iron just use a magnet. To retrieve the sulphur just put the remaining mixture in water and dissolve it. Then using a filter paper filter the solution, the sulphur which is not soluble will remain on the filter paper and to retreive the sugar from the solution just re-crystallize it.


What happened to the salt ocean water during the water cycle?

when the water evaporates, the salt from the ocean water is left behind. you can try to do this by taking some fresh water and mix it up with salt


How would you get iron from a mixture of iron and flour?

One way to separate iron from flour is by using a magnet. The magnet will attract the iron particles, allowing you to separate them from the flour. Alternatively, you could mix the mixture with water, as iron will sink to the bottom while flour will float, making it easier to separate them.


Do lipid mix with water?

No.they do not mix with water.

Related Questions

What happens when you mix lemon juice and iron?

Iron fillings will be corroded.


How could you separate a mixture of iron fillings and sulfur powder?

One method is to use a magnet to separate the iron fillings from the sulfur powder, as iron is magnetic but sulfur is not. Another method is to mix the mixture with a solvent that dissolves the sulfur powder, leaving the iron fillings behind. Lastly, heating the mixture can also cause the sulfur to sublimate, leaving the iron fillings behind.


Is iron fillings and flour a homogeneous mixture?

No, iron fillings and flour would not be considered a homogeneous mixture because they are physically distinct and do not form a uniform composition when combined. A homogeneous mixture would look the same throughout, like a solution of salt and water.


What happens when you mix iron filings and lemon juice?

When you mix iron filings with lemon juice, the acid in the lemon juice will react with the iron to produce iron oxides and hydrogen gas. The iron filings will begin to rust as the iron oxides are formed. This reaction is an example of a chemical reaction between an acid and a metal.


Are iron filings in water a suspension solution or a colloid?

They would be a suspension, at least until they sink.


Can you mix Super Shock with bleach to get the iron out of pool water?

Absolutely do not mix shock with bleach. there are chemicals specifically designed to remove Iron from the water. Ask your pool supply store. Hatawa


What is your observation when you mix a small amount of iron fillings and sulfur powder in a piece of paper and observe under a magnifying lens?

When iron fillings and sulfur powder are mixed on a piece of paper and observed under a magnifying lens, you may notice the individual particles of iron and sulfur. Upon further examination, there could be a visual indication of physical mixture of the two substances without any chemical reaction taking place.


How do you separate a mixture of iron fillings copper metal and silicon pellets?

Easy, magnet to seperate iron. water to seperate the wood because wood floats but pebbles sink.


What happened when jelly crystals mix with water?

when jelly crystals mixed with warm water will desolve.


When you mix iron and water it makes rust what is this type of rust called?

This is a normal rusting.


How do you separate a mixture that contains Iron fillings sand water and rubbing alcohol?

Here's my suggestion: Pour the full mixture through a filter paper. This will leave the water/alcohol mix in the bottom of the beaker and the iron/sand mix in the filter paper. To separate the iron and sand, I'd wait for the mix to dry and spread the mix out on a flat piece of paper. By using a magnet, you can pick out the iron filings- leaving the sand behind. The water/alcohol mix poses more problems! Hopefully, a layer will form between the two due to different densities etc. If so, one layer can be removed via a pipette. However, a more tedious method could be to... Set up a flask and sit it on a tripod and gauze. Put the mixture in the flask. GENTLY heat the flask with a Bunsen burner, with a distillation tube fitted to the flask ( also known as a reflux condenser). If the mixture isn't allowed to boil, the alcohol will evaporate away, go down the distillation vessel and into a clean beaker, leaving the water behind. Hope this is adequate?!


What do you call an iron and sulfur mix?

An iron and sulfur mix is called iron sulfide, which is also known as ferrous sulfide or iron (II) sulfide.