answersLogoWhite

0

The wire size used in a service entrance distribution panel is governed by the size of the services over current device. The larger the service, the larger the fault current could be, the larger the ground wire to carry the fault current to ground. If the largest service conductor carries 100 amps use a #8, 200 amps - #6, 400 amps - #3, 600 amps - #1, 800 amps - 1/0 and over 800 amps - 2/0 for the ground wire.

<<>>

Golden Valley Electric Assoc. in Alaska requires #4AWG copper wire for a ground from the breaker box to earth ground rod. The same goes from the service entrance panel on the pole.

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Natural Sciences

Ground wire size for 200?

The size of the ground wire for a circuit is typically based on the size of the circuit breaker protecting that circuit. For a 200 amp circuit breaker, the recommended ground wire size is 4/0 AWG (American Wire Gauge) copper wire. This wire size helps ensure that the ground wire can safely carry any fault currents that may occur in the electrical system.


When installing a circuit breaker do you size the breaker to correct wire size or the device its controlling?

When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.


What colour wire goes to the breaker using 12-2 wire?

For a typical 12-2 wire, the black wire is the &quot;hot&quot; wire that connects to the breaker, the white wire is the neutral wire that connects to the neutral bus bar, and the bare copper wire is the ground wire that connects to the ground bus bar in the circuit panel.


How big of breaker do you use for 115 volt?

Depends on the wire size used in the circuit. If you use AWG # 14 wire you must use a 15 amp breaker. If it is wired with AWG # 12 wire then you use a 20 amp breaker. If a AWG # 10 wire is used then a 30 amp breaker is required. The breaker protects the wiring from overheating so you must use the proper size breaker for the wire used.


14 gauge wire can be on what size circuit breaker?

A 14 gauge wire is typically used on a 15 amp circuit breaker. It is not recommended to use a larger circuit breaker with a smaller wire size as this can create a fire hazard.

Related Questions

Ground wire size for 200?

The size of the ground wire for a circuit is typically based on the size of the circuit breaker protecting that circuit. For a 200 amp circuit breaker, the recommended ground wire size is 4/0 AWG (American Wire Gauge) copper wire. This wire size helps ensure that the ground wire can safely carry any fault currents that may occur in the electrical system.


How do you wire a 15 amp breaker?

Ground wire connects to the ground bar, white wire connects to the neutral bar, and black wire connects to the breaker. Be sure and turn off main breaker before installing the wire or the breaker.


How do you wire a GFI breaker?

To wire a GFI (Ground Fault Circuit Interrupter) breaker, first turn off the power to the circuit. Then, connect the hot wire to the breaker's terminal, the neutral wire to the neutral bar, and the ground wire to the ground bar. Finally, attach the breaker to the panel and turn the power back on.


How do you wire an AFCI breaker?

To wire an AFCI breaker, first turn off the power to the circuit. Then, connect the hot wire to the breaker's terminal, the neutral wire to the neutral bar, and the ground wire to the ground bar. Finally, snap the breaker into place in the electrical panel.


How do you wire a wire to a wire?

If you are connecting 120 volts, you connect the black wire to the breaker, white wire to the neutral bar, and ground wire to the ground bar. If you are connecting 240 volts connect the black &amp; white wires to the breaker, &amp; ground wire to the ground bar.


What is the recommended wire size for a 50amp breaker?

The recommended wire size for a 50 amp breaker is typically 6-gauge wire.


What size wire dose a ground fault breaker use?

2.5 sq mm or 4.Sq mm coil is used for breaker in industries


When installing a circuit breaker do you size the breaker to correct wire size or the device its controlling?

When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.


What is the recommended wire size for a 20 amp breaker?

The recommended wire size for a 20 amp breaker is typically 12-gauge wire.


What is the appropriate wire size for a 25 amp breaker?

The appropriate wire size for a 25 amp breaker is typically 10 gauge wire.


What is the appropriate wire size for a 30 amp breaker?

The appropriate wire size for a 30 amp breaker is typically 10 gauge wire.


What is the recommended wire size for a 25 amp breaker?

The recommended wire size for a 25 amp breaker is typically 10 gauge wire.