0
What else can I help you with?
What is the meaning of negative watts in measuring?
Negative watts in measuring typically indicate that the device is consuming energy rather than generating it. This is common in situations where energy is being supplied to a device, such as when charging a battery or running an appliance.
What items is used to distribute heat from a Bunsen burner when heating the bottom of a crucible?
A crucible is placed in a pipestem triangle placed on an iron ring while being heated. This supports the crucible while allowing the bottom of the crucible to be directly exposed to the flame of the Bunsen burner. There is no item that is used to distribute heat from a Bunsen burner when heating the bottom of a crucible. The bottom of the crucible is intended to be exposed to the direct flame of the Bunsen burner.
Is an endodermic reaction nonspontaneous?
Yes, an endothermic reaction is nonspontaneous because it requires an input of energy to occur. This means that the reaction will not proceed on its own without external energy being supplied to drive it forward.
Where does the gas enter the Bunsen burner from?
The gas enters the Bunsen burner through a tube connected to a gas source, such as a gas line or a gas tank. The gas flows through the tube and into the burner where it mixes with air before being ignited.
How come magnets aren't a source of unlimited energy when the force between them is constant?
When standing in a bus-queue with a constant force between my feet and the ground there is no obvious source of energy, unlimited or finite. If I fall onto my neighbours shopping bag, crushing her eggs, some energy is supplied but it is limited. As soon as my body is flat on the ground there is no more energy to be had. If two magnets are held an inch apart, north opposite south and south opposite north, there will be an attractive force. There is potential energy here, and if the magnets are allowed to come together work will be done, energy supplied. This is not unlimited energy; it stops being available as soon as the magnets jam up against each other. Of course, you can recharge that energy by pulling the magnets apart, but then your muscles will have supplied the energy. The motto of physics, and of the entire universe, is TANSTAAFL. There ain't no such thing as a free lunch.
How do you know that there is energy in an electric motor?
If there is energy in an electric motor (electricity is being supplied to it). it will be turing/running. When there is no energy in it (being supplied to it) it will stop.
What is the name of electrons before energy is supplied to them?
Prior to energy being supplied to them, the electrons are named neutrons. A neutron normally breaks into a proton and an electron.
What is the wasted energy in a Bunsen burner?
The wasted energy in a Bunsen burner is primarily in the form of heat that is lost to the surroundings rather than being transferred to the reaction or process being carried out. Inefficient combustion and poor insulation can contribute to this wasted energy. Adjusting the air and gas flow rates can help minimize energy wastage in a Bunsen burner.
What are the energy that transfers to a Bunsen burner?
A Bunsen burner typically uses natural gas or propane as a fuel source. When the gas is ignited, chemical energy is converted into heat energy, which is then transferred to the object being heated through convection and radiation.
Will the matchstick ignite upon matching a Bunsen burner?
No, a matchstick will not ignite by being placed near a Bunsen burner. The matchstick needs to be struck against a rough surface to ignite the chemicals on the tip and produce a flame.
Why doesn't cold water make a hot burner cold?
Heat is a form of energy and due to the principal of thermodynamic equilibrium, will constantly seek a state of equilibrium. The reason a hot burner does not become cold is because as the energy is transferred to the cold water more energy is being put into the burner through either electricity or gas. If there was no source of energy to the burner, then the cold water would cool down the hot burner, though the cold water would also heat up in the process, to the point where both are at room temperature.
A machine has an efficiency of 91 percent If the energy supplied to the machine is 4000 watts what is the amount being used for work?
The efficiency of the machine is 91%, so the amount used for work is 91% of the energy supplied. Amount used for work = Efficiency x Energy supplied = 0.91 * 4000 watts = 3640 watts.
What would be the direction of the line graph if the energy supplied is extended five minutes longer?
If the energy supplied is extended five minutes longer, the line graph would likely show a further increase in the energy supplied over time, indicating a positive trend or upward slope. This extension would result in more energy being delivered or consumed during that additional time period.
A machine has an effciency of 91 percent if the energy is supplied to the machine is 4000 watts what is the amount being used for work?
The efficiency of a machine is given by the ratio of useful work output to the energy input. Therefore, if the machine has an efficiency of 91%, the amount being used for work would be 91% of the energy input. In this case, if the energy supplied is 4000 watts, the amount being used for work would be 0.91 * 4000 = 3640 watts.
What is the meaning of negative watts in measuring?
Negative watts in measuring typically indicate that the device is consuming energy rather than generating it. This is common in situations where energy is being supplied to a device, such as when charging a battery or running an appliance.
How do you increase the temperature of a burner flame?
To increase the temperature of a burner flame, you can either increase the flow rate of the fuel being supplied to the burner or adjust the air-to-fuel ratio to ensure complete combustion. You can also adjust the position of the air vents or dampers to allow more oxygen to mix with the fuel, resulting in a hotter flame.
What is France's primary source of power?
France is mainly supplied by electrical energy, 80 % of this electricity being produced by nuclear powerplants.
