answersLogoWhite

0

Black and Red are hot (2 slots ), white neutral , bare copper (or green) is grounding. The answer is correct, but to carify a bit...Red and black are connected to the brass colored terminals, white to silver and green or bare to the green terminal.

User Avatar

Wiki User

20y ago

What else can I help you with?

Continue Learning about Natural Sciences

When can a jumper wire be used to bridge electrical ground crossings?

A jumper wire can be used to bridge electrical ground crossings when there is a break in the ground path, leading to unreliable or no connection. By connecting the ground terminals on either side of the break using a jumper wire, you can establish a reliable ground connection and ensure proper functioning of the electrical circuit. It is important to use proper gauge wire and ensure proper insulation to prevent any electrical hazards.


Do you put electrical tape around a spliced ground wire?

No, it is not recommended to put electrical tape around a spliced ground wire. The ground wire should be securely connected using a wire nut or another appropriate connector as specified in electrical codes to ensure a reliable connection and safety.


How do you earth a computer?

Most home or commercial building wiring uses 3 prong power outlets. One of the pins on a plug SHOULD be the ground/earth wire.If the power cable was created properly, the computer should be properly grounded (earthed) when it is connected to the main power through that plug...HOWEVERIf there is any doubt as to whether your power outlet has a built in ground connection, you can connect a single (12 GA or 14 GA) wire to an iron or copper pipe in the home or drive a grounding rod into the ground outside the home and connect the wire to that. Run the wire to the computer and place a crimp-on lug to the end of the wire, then connect it to the computer chassis using one of the screws on the back of the computer.


How can you read a ground fault using a meter?

To read a ground fault using a meter, you can use a digital multimeter set to measure resistance. Disconnect the ground wire and touch one probe to the ground wire and the other probe to the ground terminal. A reading of 0 ohms indicates a direct short to ground and signifies a ground fault.


Should the black wire be bonded to the ground?

It depends on the color coding standards for what country you are in. In the US, the answer is no. The Neutral (white wire) is grounded at the service entrance to the building. The black wire should have roughly the same voltage to the neutral and to the ground. Something to be aware of: If you are using a meter and checking for continuity between the black wire and ground, it may tell you that they have continuity if the breaker is on.

Related Questions

What is the proper technique for achieving a secure electrical connection using a ground crimp?

To achieve a secure electrical connection using a ground crimp, strip the wire insulation, insert the wire into the crimp connector, and use a crimping tool to compress the connector onto the wire. Ensure the connection is tight and secure to prevent electrical issues.


What do you do if your xbox 360 has sound but no color?

If your Xbox 360 gaming console has sound but no color then this could be a problem with your HDMI connection. Try using a different cable.


Why is Satan depicted as using a pitchfork?

This is a melding of the mythological being hades who had a two pronged fork for destroying stuff.


How do you communicate between two xbee modules using pic 16f887?

3 point connection: 1. Ground to Ground 2. xBee DOUT to 16F887 RC7 3. xBee DIN to 16F887 RC6


What are the three forms of connection?

The three forms of connection are physical connection (e.g., using cables or wires), wireless connection (e.g., using Wi-Fi or Bluetooth), and virtual connection (e.g., using the internet to connect remotely).


When can a jumper wire be used to bridge electrical ground crossings?

A jumper wire can be used to bridge electrical ground crossings when there is a break in the ground path, leading to unreliable or no connection. By connecting the ground terminals on either side of the break using a jumper wire, you can establish a reliable ground connection and ensure proper functioning of the electrical circuit. It is important to use proper gauge wire and ensure proper insulation to prevent any electrical hazards.


In facial make up what is color makeup?

Color is anything that isn't skin-colored.Foundation, powder and concealer are ground; everything else is color. Some artists say anything that goes on the eyes or lips is color and everything else is ground, which would take bronzer and blush out of the color category.I say bronzer is ground and blush is color, unless I'm using bronzer as blush and sometimes I do.If my subject has really nice naturally high cheekbones sometimes I just put a little bronzer on them for color and don't worry about using a pink-toned blusher.I've also used bronzer as blush on very light skinned women of color, and that works okay.Anyway, if it's not (a wide range of) beige in color it's usually considered "color."


In US Canada or countries using similar mains supplies if the Neutrals are White what color is Ground Or is the Ground wire never colored at all i.e. is it always bare metal with no insulating sheath?

The ground can be either green or bare.


How do you connection database in HTML using javascript?

Connection Database can be established using language such as Java. For that you need to create an object of Connection type.


What does wireless connection offer?

Connection with using copper wire


What does the term three pronged attack mean?

It is when an objective is assaulted by Three or more units either on multiple sides or by using multiple weapon systems


Why is it important to grease a ground glass joint before using it?

It is important to grease a ground glass joint before using it to create a tight seal and prevent leaks or damage to the glassware. Greasing the joint helps to ensure a secure connection and smooth assembly, which is crucial for accurate and safe experimentation in a laboratory setting.