answersLogoWhite

0

Any where that a three phase supply distribution is needed to operate three phase equipment.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Natural Sciences

What is the difference between single phase transformer and three phase transformer?

A single phase power supply has two "hot" legs or conductors which have a sine wave that are 180 degrees apart. A three phase power supply has three "hot" conductors which have a sine wave that are 120 degrees apart. You can thank Nicoli Tesla, whose birthday is today for the three phase or polyphase power supply and of course all alternating current!


What type of electrical current is used for three phase 408V?

Three-phase 408V systems typically use alternating current (AC).


Does the formula used to calculate the turns ratio uses the phase voltages and phase current?

For a transformer, the turns ratio always applies between its primary and secondary windings. So the turns ratio for a three-phase transformer is the ratio of primary to secondary phase voltages, not between line voltages.


Can a single phase supply be used in a three phase supply?

No, a single-phase supply cannot be directly used in a three-phase system. The voltages and phases are different, so additional equipment such as a phase converter or transformer would be needed to convert the single-phase supply to match the requirements of the three-phase system.


What is DY11 transformer?

A DY11 transformer is a three-phase transformer configuration where the high voltage winding is connected in a delta (Δ) configuration and the low voltage winding is connected in a star (Y) configuration. This configuration is commonly used in power distribution systems to step down high voltage to a lower voltage for industrial and commercial applications.

Related Questions

Would you install three-phase transformer or bank of three single phase transformer in a large power station and justify by comparing the two schemes?

A three-phase transformer bank is often used in power stations because it is easier to construct and transport very large single-phase transformers, compared with constructing and transforming an equivalent-capacity three-phase transformer.


Why would you use a three phase transformer in place of a single phase transformer?

the necesscity of two three phase transformers operating in parallel are as follows...if the one transformer fails to give supply,then another transformer can be used in parallel and hance,continuity of supply can be maintained.one transformer can be easily take out from the supply for repair & maintanance.if the load on the substation increases beyond the rated values of transformer, then another transformer can be used to share rhe load of the substation.


Is there a basic difference between a three phase power transformer and a three phase distribution transformer?

The basic difference is the secondary voltages. On a distribution transformer the secondary voltage is very high. This is to overcome line loss for transmission of electricity over long distances. A three phase power transformer is used at the consumers three phase services end to manipulate voltages that consumers need to operate their equipment. The transformer that feeds your house is considered to be a single phase power transformer.


What is Advantage of 3 phase transformer?

The type of transformer is dictated by the type of supply. A three-phase supply is used in power distribution because it dispenses with half the wire and therefore half the power losses in the circuit. In principle a three-phase transformer could be replaced by three separate single-phase transformers to provide the same service, but there would be double the mass of transformers, in other words the three single-phase transformers would be twice the weight of the three-phase transformer.


Basic operation of a 3-phase transformer?

Three Phase transformers have three windings. If connected in Delta, it will have R Y B phase winding, voltage between RY, YB and BR. Phase voltage and line voltage are same. If connected in Star, there will be a neutral as well with RYB. Line voltage and Phase voltage are different. Line voltage = 1.73 x Phase voltage.


Can 3 single phase transformers can replace 1 three phase transformer?

Yes, you can use three single phase transformers on three phase applications and interconnect them to serve as a single transformer or you could use one single phase transformer fed from two of the three lines in a step down application.


What is the xo terminal on a transformer used for?

The XO denotes the joined secondary terminal connection of three single coils of a three phase transformer. It is the common return on any unbalanced current of a three phase system.


Does open delta three phase transformer connection is used to convert three phase to two phase?

Two phase is not used anywhere. What you may be thinking is center tapped single phase (negative voltage at one terminal, neutral at 0, and positive at the other, all in phase so you can get 120 volts or 240 volts). Open delta would be used for three phase power. A single transformer can be used for single phase power. If you have limitted three phase power, and mostly single phase power needs, two transformers could be connected to provide both.Another AnswerAn 'open-delta' connection is used to provide a temporary three-phase supply to a load, from a three-phase transformer bank when one of the transformers has been removed due to failure. Linesmen can rewire the remaining two transformers in such a way that they still provide a three-phase supply, albeit at a reduced capacity.The open-delta connection can also be used to provide an initial (lower-cost) three-phase supply to a load when an increase in that load is anticipated at some time in the future. Adding a third-transformer then adds capacity to the existing transformer bank to match the predicted load increase.Two-phase systems are archaic and are unlikely to be encountered, these days. They are provided by alternators with two armature windings, displaced by 90 degrees.


What is the difference between single phase transformer and three phase transformer?

A single phase power supply has two "hot" legs or conductors which have a sine wave that are 180 degrees apart. A three phase power supply has three "hot" conductors which have a sine wave that are 120 degrees apart. You can thank Nicoli Tesla, whose birthday is today for the three phase or polyphase power supply and of course all alternating current!


How you differentiate between single phase and three phase transformer?

A single-phase transformer works with a single-phase supply, while a 3-phase transformer is used with a 3-phase supply. A single-phase transformer has 2 wires on the primary and secondary (ignoring taps) while a 3-phase tansformer has 3 or 4 wires on the primary and secondary.


What are the different types of transformers?

A small list of transformers1. Distribution Transformers2. Padmount Transformers3. Station Transformers4. Station Transformers Various specific electrical application designs require a variety of transformer types. Although they all share the basic characteristic transformer principles, they are customize in construction or electrical properties for certain installation requirements or circuit conditions.Autotransformer: Transformer in which part of the winding is common to both primary and secondary circuits.Capacitor voltage transformer: Transformer in which capacitor divider is used to reduce high voltage before application to the primary winding.Distribution transformer, power transformer: International standards make a distinction in terms of distribution transformers being used to distribute energy from transmission lines and networks for local consumption and power transformers being used to transfer electric energy between the generator and distribution primary circuits.Phase angle regulating transformer: A specialized transformer used to control the flow of real power on three-phase electricity transmission networks.Scott-T transformer: Transformer used for phase transformation from three-phase to two-phase and vice versa.Polyphase transformer: Any transformer with more than one phase.Grounding transformer: Transformer used for grounding three-phase circuits to create a neutral in a three wire system, using a wye-delta transformer,[85][90] or more commonly, a zigzag grounding winding.Leakage transformer: Transformer that has loosely coupled windings.Resonant transformer: Transformer that uses resonance to generate a high secondary voltage.Audio transformer: Transformer used in audio equipment.Output transformer: Transformer used to match the output of a valve amplifier to its load.Instrument transformer: Potential or current transformer used to accurately and safely represent voltage, current or phase position of high voltage or high power circuits.Pulse transformer: Specialized small-signal transformer used to transmit digital signaling while providing electrical isolation.


What are different types of transforms?

A small list of Transformers1. Distribution Transformers2. Padmount Transformers3. Station Transformers4. Station Transformers Various specific electrical application designs require a variety of transformer types. Although they all share the basic characteristic transformer principles, they are customize in construction or electrical properties for certain installation requirements or circuit conditions.Autotransformer: Transformer in which part of the winding is common to both primary and secondary circuits.Capacitor voltage transformer: Transformer in which capacitor divider is used to reduce high voltage before application to the primary winding.Distribution transformer, power transformer: International standards make a distinction in terms of distribution transformers being used to distribute energy from transmission lines and networks for local consumption and power transformers being used to transfer electric energy between the generator and distribution primary circuits.Phase angle regulating transformer: A specialized transformer used to control the flow of real power on three-phase electricity transmission networks.Scott-T transformer: Transformer used for phase transformation from three-phase to two-phase and vice versa.Polyphase transformer: Any transformer with more than one phase.Grounding transformer: Transformer used for grounding three-phase circuits to create a neutral in a three wire system, using a wye-delta transformer,[85][90] or more commonly, a zigzag grounding winding.Leakage transformer: Transformer that has loosely coupled windings.Resonant transformer: Transformer that uses resonance to generate a high secondary voltage.Audio transformer: Transformer used in audio equipment.Output transformer: Transformer used to match the output of a valve amplifier to its load.Instrument transformer: Potential or current transformer used to accurately and safely represent voltage, current or phase position of high voltage or high power circuits.Pulse transformer: Specialized small-signal transformer used to transmit digital signaling while providing electrical isolation.