0
Dependant to manufacture that ground could be either black or white. But to be sure not to trial and error ti find out the hard way as smoke means not right and bad such decision testing on a gamble gone bad, this will help- componet body should be grounded, check lead to full continuity to ground - there could be answer but to all plastic or within insulated circuits etc, to addition wiring besides black and white even or switching pre-componets before power connections vs: direct connect to power supply, both or multi componets willl have a direct to ground as a rule to componets outside of internal circuitry, should be positive/ hot is switched also in residential wiring to a switched off circuit, the outlet of lamp should be all neutral or ground. Keep rule in mind to save you to electrical and seeing red wire is switched circuit feed is always bottom & output from top, to switched device Is red. Seeing red at lamp or outlet is automatic as feed from switch like in photocell or motion detection autoswitch in security lamp turning on perimeter lighting or night lights etc. But to such 12 volt system with white, black and red, should follow same rules as instance to thermo-switched liquid heater system with power connections being white & red with heater leads being white & black, both componets have shared white wires / leads, having to what possibly necessary to verify even if other componet to continuity check body to suspected ground wire being in this specific situation as white being ground switched circuit is black. To 12 volt yellow is naturally a memory wire with necessary connection to unswitched positive and blue wires are remote relayed power turn on as its required power
to turn on with lower voltage supply wire such as power output from radio or manual switch to turn in audio amplifiers, but such also output from radio is also blue in needed consideration to componet the switched or supplied signal
What else can I help you with?
Connecting black and white wires to 306 angel eyes?
Just simply, connect all the black wires to the black wire coming out of the connector, and all the white wires to the white wire coming out of the connected. Use the blocks with screw in to connect them (pick them up from most car accessories shops like halfords, wilcos....etc).
Outside porch lamp has no box just two wires coming in black wires are tied and don't connect to fixture just the white wires what is going on here?
You would have to provide more info to be certain what your problem is. Typically a black and white wire would connect to the two wires on the light fixture. The fixture should also be controlled by a switch that "breaks" the black (Hot Wire) to turn off the fixture. If you have a volt meter you can see if there is 120Volts between the black and white wires with switch on. If there is a single white wire going to fixture (Neutral), where is the "black wires tied" to. Maybe one of the black wires has broken off the fixture.
How do you wire two outside light sensing motion porch lights that are controlled from one switch with each light having a white black ground and optional red wire?
Connect the black wire from the switch to the black wires of both lights. Connect the white wires together. Connect the red wire, if used for the motion sensor, to the black wires on the lights. Connect all ground wires together and to the ground terminal on the switch. Make sure to turn off power before connecting any wires for safety.
How do you wire alight fixture with three black wires three white wires three grounds?
You will connect the three black wires together, the three white wires together, and the three ground wires together. Use wire nuts to secure the connections. Follow the manufacturer's instructions and make sure to turn off the power before proceeding.
Trying to install an IKEA light The light has black white and 2 yellow and green striped wires Ceiling box has 2 black 2 red and white wire Room has 2 switches What should connect to what?
Connect the black wire from the ceiling box to the black wire on the light. Connect the white wire from the ceiling box to the white wire on the light. The yellow and green striped wires from the light are likely the ground wires, secure these to the green or bare copper wire in the ceiling box. Cap off or tape the red wires from the ceiling box, as they are likely for a separate function and are not needed for the light fixture.
Connecting black and white wires to 306 angel eyes?
Just simply, connect all the black wires to the black wire coming out of the connector, and all the white wires to the white wire coming out of the connected. Use the blocks with screw in to connect them (pick them up from most car accessories shops like halfords, wilcos....etc).
What color wires should be used to connect an outlet: red, black, or white?
The white wire is typically used to connect an outlet.
What is the proper way to connect red, white, and black wires to an outlet?
To connect red, white, and black wires to an outlet, you should match the colors of the wires to the corresponding screws on the outlet. The black wire connects to the brass or black screw, the white wire connects to the silver or white screw, and the red wire connects to the brass or black screw. Make sure to tighten the screws securely to ensure a proper connection.
What is the standard color coding for white and black electrical wires in a typical household wiring system?
In a typical household wiring system, the standard color coding for electrical wires is white for neutral wires and black for hot wires.
Outside porch lamp has no box just two wires coming in black wires are tied and don't connect to fixture just the white wires what is going on here?
You would have to provide more info to be certain what your problem is. Typically a black and white wire would connect to the two wires on the light fixture. The fixture should also be controlled by a switch that "breaks" the black (Hot Wire) to turn off the fixture. If you have a volt meter you can see if there is 120Volts between the black and white wires with switch on. If there is a single white wire going to fixture (Neutral), where is the "black wires tied" to. Maybe one of the black wires has broken off the fixture.
Can you run power from a light fixture to another light fixture?
Yes. Connect Black to Black, White to White and bare ground wires together.
What are the different color options available for the wires in the electrical system, including black, white, and green?
The different color options available for wires in an electrical system include black, white, and green.
How do you wire two outside light sensing motion porch lights that are controlled from one switch with each light having a white black ground and optional red wire?
Connect the black wire from the switch to the black wires of both lights. Connect the white wires together. Connect the red wire, if used for the motion sensor, to the black wires on the lights. Connect all ground wires together and to the ground terminal on the switch. Make sure to turn off power before connecting any wires for safety.
What is the proper way to connect white, black, and green wires in an electrical circuit?
To properly connect white, black, and green wires in an electrical circuit, you should match the white wire to the neutral terminal, the black wire to the hot terminal, and the green wire to the ground terminal. This ensures the safe and effective flow of electricity in the circuit.
How do you install 220 receptacle with white black and bare wires?
Assuming the wires are the correct gauge for application and breaker you use black and white wires as hot. Put red electrical tape on each end of white wire and connect red and black to the breaker output and bare wire to ground lug in panel. At receptacle connect black and red to hot contacts and bare wire to ground lug.
Where does the red wire in a baseboard heater connect to the black or white wire in the wall?
In the heater you will have two wires. You should then have 2 supply wires from the panel, and 2 wires from the thermostat. The neutral (white) supply wire should go to one of the wires on the heater. The hot (black) supply wire should connect to one wire from the thermostat. The other wire from the thermostat will connect to the other wire from the heater.
If the old block heater cord of a 1988 Honda CRX had two wires and the new end has 3 which colored wires connect the new connector to the old one?
Connect to two wires you have to the the spade connectors and forget the ground connector. The spade connector wires should be black and white. Black to gold and white to silver. If the wires coming from the heater happen to be red and white, then red goes to black. You could buy a simple lamp cord which has only tow wires.
