Watts = Amps x Volts. Amps = Watts/Volts. 10000/120 = 83.3 amps can be used at 120 volts. On a generator that large it is most likely that it also has the capacity to produce 240 volts. 10000/240 = 41.6 amps can be used at 240 volts. What you can connect to the generator will be totals of the amperage of devices that do not go above these amp ratings.
Use the formula I = W/E, Amps = Watts/Volts. Apply the voltage of the generator to the formula and the results will be the amount of amperage the generator will produce.
75 Amps theoretically Need to know if the generator is 3 phase or single phase.
Yes, some models of Onan generators have the capability to output 240 volts. Make sure to check the specifications of the specific generator model you are using to confirm if it can provide 240 volts.
Small generators are sized in watts. Watts is the product of amps times volts. To properly answer this question a voltage for your 10 amps must be stated. That said small generator outputs are usually 120/240 volts in North America. So 10 amps at 120 volts equal 1200 watts. 10 amps at 240 volts equal 2400 watts. A 3000 watt generator will be amply for your 10 amp load.
Watts = Amps x Volts. Amps = Watts/Volts. 10000/120 = 83.3 amps can be used at 120 volts. On a generator that large it is most likely that it also has the capacity to produce 240 volts. 10000/240 = 41.6 amps can be used at 240 volts. What you can connect to the generator will be totals of the amperage of devices that do not go above these amp ratings.
Use the formula I = W/E, Amps = Watts/Volts. Apply the voltage of the generator to the formula and the results will be the amount of amperage the generator will produce.
This depends on what you are meaning by "Average". A typical small generator you can throw in the back of a truck will produce 120 volts, some can do 240. Building backup generators would produce whatever voltage is needed for that building (if it's a plant that using 480 volts, it will produce 480 volts). "Large" Wind turbine generators often produce 600-1000 volts; good sized power plants (100MW and up) will typically have a terminal voltage of 10-30kV.
75 Amps theoretically Need to know if the generator is 3 phase or single phase.
If your generator is rated at 1000 watts continuous......and you are using 120V.....available amps are 1000/120 =8.3 .
Yes, some models of Onan generators have the capability to output 240 volts. Make sure to check the specifications of the specific generator model you are using to confirm if it can provide 240 volts.
Small generators are sized in watts. Watts is the product of amps times volts. To properly answer this question a voltage for your 10 amps must be stated. That said small generator outputs are usually 120/240 volts in North America. So 10 amps at 120 volts equal 1200 watts. 10 amps at 240 volts equal 2400 watts. A 3000 watt generator will be amply for your 10 amp load.
No, the generator must output 220 volts which any generator I have ever seen does.
500,000 watts/240 volts = 2,083.34 Amps (single phase)
When the term "double 20 amp circuit" is used, the presumption is that, it is 20 amps at 240 volts. If your generator has the breaker built in then, yes, you have the capacity to run 240 volt devices from your generator.
The unit of power is expressed in watts, and the product of current (Amps) and voltage (volts) is power there fore if you multiply the amps and the volts give watts. so 20 x 240 will give you a 4800 watts of power.
pass 240 volts through it