answersLogoWhite

0

Degradation

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

Can rubber bands burn?

Yes rubber can burn but it takes time


What are some disadvantages to rubber bands?

Rubber bands can degrade over time, losing their elasticity and becoming brittle. They can break easily if stretched beyond their limits. Rubber bands can also cause allergic reactions in some individuals.


Why are some rubber bands more flexible than others?

Rubber bands vary in flexibility due to differences in their composition and manufacturing process. Factors such as the type of rubber used, the thickness of the band, and the stretching capacity can all influence the overall flexibility of a rubber band. Additionally, the age and storage conditions of rubber bands can also impact their flexibility over time.


Why do rubber bands dry out?

Rubber bands dry out due to the loss of moisture in their material over time. Exposure to sunlight, air, and heat can cause the rubber in the bands to become stiff and brittle, leading to dryness and potential breakage.


How much does it cost to make a rubber?

Making rubber bands costs less than two cents per piece depending on the brand. Many rubber bands can be produced in a very short period of time.


How do you make sticky rubber normal?

baby powder. Once the rubber deteriorates, there is no satisfactory method to "cure" it, except to have the component replaced. The following, however, are some suggestions that are commonly put forward: 1. Strip away the rubber coating altogether, if you can live with that! Some have reported success in using alcohol to strip away the rubber, taking care not to damage the surfaces on surrounding components. Or simply peel it off bit by bit. 2. Use talc or baby powder to apply to the sticky surface (Caution: this will not work for long! And don't use on cameras with sticky rubber backs--the powder will get into the camera and spoil it). 3. Use diluted ammonia or Windex to wipe the sticky surface away (but result is not permanent). 4. Check those who sell supplies for rubber boats, and get a special paint that will coat over the rubber to treat it. 5. I had success using a little paint thinner to remove the stickiness on some rubber cables. The thinner is applied onto a cloth and using it to rub on the sticky surface until the stickiness is gone. The stickiness, I suspect, was due to contact with masking tape, which reacts with the rubber after being on it for a long time. This was the most successful experience with treating sticky rubber surfaces thus far.


Why do rubber bands become brittle over time or dry rot?

Rubber bands become brittle over time primarily due to a process called oxidation, where exposure to air and UV light breaks down the rubber's molecular structure. Additionally, loss of moisture from the rubber can lead to drying and cracking, a phenomenon often referred to as dry rot. Environmental factors such as temperature fluctuations and exposure to chemicals can further accelerate this degradation, causing the rubber to lose its elasticity and flexibility. As a result, old rubber bands can become stiff and break easily.


Is Blake Cummings a name?

yep and he"s in 6th grade.......... he shoots me with rubber bands all the time in the face...


Why does rubber bend?

rubber is not strong on its own but when it is vulcanised,i.e.,heated with sulphur to a definite temperaturefor a known period of time,it becomes strong because sulphur atoms act as bridges between rubber molecules, initiate cross-linking and convert the soft sticky rubber into a hard, elastic mass which can be put to extensive uses such as use in tyres,etc Because it is elastic.


How much does it cost to make a rubber band?

It depends on how big you want the ball to be. You can probably make a reasonable sized one with 100-200 rubber bands. One of the big bags you can find in an office supply store would probably be enough to start out with.


How do you put rubber bands on braces?

Well, Rubber bands are given to you by your orthodontist. If they showed you how to do it, and you can't remember, or they didn't take the time to show you, here is how to attach them. First of all, you need the small rubber bands from your orthodontist. Now you hook it on one of the hooks, and stretch it gently to the next hook. If you can't do it with your fingers, try using tweezers, because it can reach in small areas. Make sure you wash your hands first, and take them out before eating! Good Luck!


What are the two types of rubber bands for braces?

Two types of rubber bands that are available for braces are single elastic ligatures and connected elastic ligatures. Both ligatures are available in a variety of colours and would need to be changed at every appointment as they lose strength over time.