its probably old get an electrician to replace it
Open up the ceiling box and disconnect the blue wire coming from the light and connect it to the black wire coming from the fan. Be sure and put a wire nut on the wire where the light was connected before you removed it. The wall switch is controlling power to the wire where the fan is connected so when you connect the blue fan wire to that connection you will be sending power to both the fan and light from the wall switch.
The plastic rectangle thingy around a light switch is generally called a "wall plate." As outlets also have wall plates, the phrase "switch plate" is more descriptive, but less commonly used.They do not necessarily have to be plastic.
Yes. Simply turn on the ceiling fan while the light switch is in the "on" position. Adjust the spinning to the level of your choice. Now the fan will turn on and off when you switch the light on and off.
No, you only pay for the power used. Light on you pay, light off no cost.
Not wanting to state the obvious but the wall switch has to be turned on to supply voltage to the outlet. The lamp will need a three way light bulb in the lamp. A three way bulb uses two filaments of different lengths. One element is used for low brightness, the other filament for medium brightness and the high brightness setting uses both filaments in the bulb. If a single filament ordinary light bulb is used in place of a three way light bulb there will be a position on the three way lamp switch where the bulb will not light. Find the position on the lamp where the bulb will light and leave it there. Use the wall switch to turn the lamp off and on through the controlled receptacle.
When you turn off the wall switch, it breaks the circuit that allows electricity to flow to the light bulb, causing the light to go out.
To install a smart light switch in your home, follow these steps: Turn off the power to the light switch at the circuit breaker. Remove the existing light switch from the wall. Connect the wires from the smart light switch to the corresponding wires in the wall. Secure the smart light switch to the wall. Turn the power back on at the circuit breaker. Follow the manufacturer's instructions to set up and connect the smart light switch to your home's Wi-Fi network.
A toggle switch is either off or on, depending in which position it has been manually switched to. An example is the wall switch that operates the light in a room - it is either off or on. It toggles between off or on.
Well the light switch on the wall will make and break the electrical connection, making the light go on and off.
To install a horizontal light switch in your home, follow these steps: Turn off the power to the circuit at the breaker box. Remove the existing switch plate and switch from the wall. Connect the wires from the new horizontal light switch to the corresponding wires in the wall using wire nuts. Secure the switch to the wall with screws. Attach the switch plate to cover the switch. Turn the power back on and test the switch to ensure it is working properly.
Some rooms have an outlet controlled by a light switch at the door. This is normally in bedrooms. It is possible that the switch is wired to only one of two outlets in a duplex outlet since it is easy to configure a duplex outlet to separate the bottom and top outlets.
A pull chain light works by using a chain that is connected to a switch inside the light fixture. When you pull the chain, it activates the switch, turning the light on or off. The main features of a pull chain light are its convenience in easily turning the light on and off without the need for a separate wall switch, and its simple and traditional design that is commonly found in older homes or in areas where a wall switch is not practical.
To install a motion sensor light switch for outdoor use, follow these steps: Turn off the power to the existing light switch at the circuit breaker. Remove the existing light switch cover and switch from the wall. Connect the wires from the motion sensor light switch to the existing wires in the wall, following the manufacturer's instructions. Secure the motion sensor light switch to the wall and replace the cover. Turn the power back on at the circuit breaker and test the motion sensor light switch to ensure it is working properly.
The problem is at the wall switch. Over time they corrode which is very dangerous. I assume light is controlled by a single switch and not a 3-way.
(this should be a grammar question) Switch off the light(s).
To install a dimmer light switch, first turn off the power to the light switch at the circuit breaker. Remove the existing switch plate and switch from the wall. Connect the dimmer switch wires to the corresponding wires in the wall box, following the manufacturer's instructions. Secure the dimmer switch in place and attach the switch plate. Turn the power back on and test the dimmer switch to ensure it is working properly.
To install a flush light switch in your home, first turn off the power to the circuit at the breaker box. Remove the existing switch plate and switch from the wall. Connect the wires from the new flush light switch to the corresponding wires in the wall using wire connectors. Secure the switch in place and attach the switch plate. Turn the power back on and test the switch to ensure it is working properly.