answersLogoWhite

0

Rinsing a buret with a base before use helps to remove any impurities or contaminants that may be present in the buret. It also ensures that the base solution will come into contact with the entire surface area of the buret, allowing for more accurate and consistent volume measurements during titrations.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Natural Sciences

How a buret is filled up?

To fill a buret, close the stopcock at the bottom, pour the solution into the top of the buret, open the stopcock slightly to allow air bubbles to escape, and then close the stopcock once the solution reaches the zero mark on the scale. Adjust the meniscus by gently tapping the buret if needed.


Can a chipped or broken buret tip can deliver accurate results?

A chipped or broken buret tip can affect the accuracy of results by causing leaks or uneven flow rates. It is important to replace the buret if it is damaged to ensure precise measurements.


What is a buret brush used for?

A buret brush is used for cleaning burets, which are long, narrow glass tubes used in laboratories for measuring and dispensing precise volumes of liquid. The buret brush is designed to reach the inside of the buret to scrub away any residue or contaminants that may be present.


What is a buret clamp?

A buret clamp is a chemistry laboratory support device, to affix and hold steady another piece of equipment (a glass column called a buret) which will be reacted with chemicals. The clamp has holding jaws, which are curved to firmly grasp the column in two portions of its long axis. It also has an attachment, by which it grasps the support post. The clamp is a piece of hardware which makes a retaining bridge between the ground support post, and the chemically reactive vessel. There are several basic designs and makes of buret clamps, which serve to accomodate the choices and work detail, of the chemist.


Why must you fill the buret only when its top is below eye level?

Filling the buret below eye level helps to prevent splashing or spilling chemicals, which could be hazardous. It also ensures accuracy in reading the meniscus level when adding solutions to the buret. It is a safety precaution to minimize the risk of exposure to harmful chemicals.

Related Questions

When rinsing a buret after cleaning it with soap and water should the rinse be dispensed through the buret tip or the top of the buret?

tip


Should you dispense a buret rinse through the top or the tip?

You should dispense a buret rinse through the tip to ensure proper cleaning and prevent air bubbles from forming in the buret. This method also helps to remove any residual liquid or contaminants from the buret.


When rinsing a buret after cleaning it with soap and water should the rinse be dispensed through the buret tip or the top opening of the buret?

The rinse should be dispensed through the buret tip to ensure that any soap residue or impurities are flushed out completely. This method ensures that the buret is thoroughly cleaned and ready for its next use.


How a buret and pipette are cleaned for use in titration?

To clean a buret and pipette for use in titration, you should first rinse them with distilled water to remove any residue. Next, wash them with a suitable cleaning solution, such as a diluted acid or base depending on the titrant used. Finally, rinse them with distilled water again and allow them to dry before use.


Why do you take acid in buret?

because ,we don't suck the acid ,pipet used for sucking ,so we take base in pipet and take acid in buret.


What is the use of a buret clamp?

to clamp the buret


How to use a buret properly for accurate measurements?

To use a buret properly for accurate measurements, first rinse the buret with the solution you will be using to remove any impurities. Then, fill the buret with the solution, making sure there are no air bubbles. Record the initial volume reading. Slowly add the solution to the receiving flask while swirling gently. When you reach the desired volume, record the final volume reading. Subtract the initial volume from the final volume to determine the volume of solution dispensed.


What is Le Buret's population?

The population of Le Buret is 302.


When was Maurice Buret born?

Maurice Buret was born in 1909.


When did Maurice Buret die?

Maurice Buret died in 2003.


What is the area of Le Buret?

The area of Le Buret is 12.92 square kilometers.


What is a buret?

A buret is a glass tube with fine gradations and a stopcock at the bottom, used in laboratory procedures.