0
Why should the lower rather than the upper hose barb be used for the water inlet in simple distillation?
Using the lower hose barb for the water inlet in simple distillation ensures better and more efficient cooling of the condenser. It allows the water to flow in a counter-current direction to the vapor, maximizing the cooling effect. This helps to efficiently condense the vapor back into liquid form.
What else can I help you with?
In distillation the water inlet is down why?
In distillation, the water inlet is typically located at the bottom of the distillation column because this allows for more efficient heat transfer and vaporization of the liquid being distilled. By introducing water at the bottom, it helps to create an upward flow of vapor, which improves separation of components in the mixture.
Why should the water-inlet be at the lower end of the condenser?
The water inlet should be at the lower end of the condenser to ensure proper cooling efficiency. Placing it at the lower end allows for better circulation of the cooling water, which helps in maximizing heat transfer and improving the overall condensation process. This arrangement also helps in preventing air pockets from forming in the condenser, which could hinder its effectiveness.
What will be effect if high temperature shift converter inlet temperature decrease?
If the temperature is less than the temoerature requ ired for reaction to proceed,higher co slip will result.Decreasing the inlet temperature to optimum inlet temperature will result in more conversion.
What is a wide inlet of the sea that is parallel to the coastlines?
Fjord, also spelled fiord, is a narrow inlet along a coastline. Fjords are created by glacial erosion. There are many fiords in Europe.
What should be the range of temperature of flue gases at outlet of air pre-heater?
The typical flue gas temp at the inlet to the air heater is about 650-750 DegF range.
In distillation the water inlet is down why?
In distillation, the water inlet is typically located at the bottom of the distillation column because this allows for more efficient heat transfer and vaporization of the liquid being distilled. By introducing water at the bottom, it helps to create an upward flow of vapor, which improves separation of components in the mixture.
How do you change your thermostat on your 2003 Chevy Impala?
The thermostat should be on the top of the engine under the water inlet. Drain the radiator. Remove the top radiator hose from the inlet. Unbolt the inlet, and pull the thermostat out for replacement.
Can the water inlet and outlet in distillation be inter converted?
No. Remember: hot air rises & cool air sinks. If the water outlet was to be placed below the condenser, the heat of the water would rise and linger in the condenser, making the condensation process inefficient.
What is an example of an inlet?
I know a couple examples, all of which are in Long Island, NY: Shinnecock Inlet Rockaway Inlet East Rockaway Inlet Fire Island Inlet Moriches Inlet
What should you do if your Bunsen burner goes out?
Shut off the gas and let any free gas clear out. The next thing you should do is check the lines to see if there is a leak. Next, check to see if the knobs controlling the air inlet and gas inlet are correct. If the air inlet is closed, there will be no combustion and no flame. Same goes for the gas inlet. Fiddle with these until you have the flame desired. If this does not fix the problem of the burner going out, try a different one.
What temp should a cadalic converter be?
A healthy catalytic converter will be hotter out the back outlet than the front inlet after a good highway run. Average temp should be aprox 450 degrees at the front inlet to 700 degrees out the rear.
1996 explorer where is the heater inlet line in a 1996 ford explorer?
It should be the same as my 1995 - at the firewall the heater hose nearest the drivers side is the inlet hose to the heater core
Bypass heater core on 2001 Pontiac sunfire?
Simple, take the inlet and outlet hoses going to and from the heater core and connect them together.
Where is thermostat located 1995 Mercedes Benz s500 thermostat replacement?
The thermostat should be located in the top radiator hose inlet at the engine. The hose and inlet need to be removed to change the thermostat.
What should be the gap for the tappets on a 1993 Ford Fiesta 1.3?
Inlet valves should be 0.2 mm Exhaust valves should be 0.3 mm
Where is the Town Of Inlet Public Library in Inlet located?
The address of the Town Of Inlet Public Library is: 164 N. Rt. 28, Inlet, 13360 0274
Where is the Inlet Historical Society in Inlet New York located?
The address of the Inlet Historical Society is: Po Box 473, Inlet, NY 13360-0473
