white. Screws on that side (neutral) should be silver. "Brass" side gets the Black (hot) wire.
No, the wide prong is neutral it is the white wire. The narrow prong is hot it is the black wire. The round prong (in a 3 wire plug) is safety ground it is the green wire.
The wide blade is the neutral and the narrow one is the hot.
The ground blade is the longest in a three blade plug.
In North America the connections for a 15 amp cap (plug) goes as follows. Looking at the plug from the blade side directly on you should see a larger blade (silver) on the right, smaller (brass) blade on the left and a U shaped ground blade on the bottom. The white wire connects under the right (silver) coloured screw, the black wire connects under the left (brass) coloured screw and the green wire under the green ground screw.
To correctly wire a three-blade 220-volt plug, you should connect the hot wires (usually black and red) to the brass-colored screws, the neutral wire (usually white) to the silver-colored screw, and the ground wire (usually green or bare copper) to the green screw. Always make sure to follow the specific instructions provided by the plug's manufacturer and to disconnect power before working on any electrical connections.
On a 3 wire plug (NEMA 5 configuration, 125v 2 pole 3 wire grounding) the narrow blade is the "hot" lead, the wide blade is the neutral lead, and the U shaped prong is the equipment grounding conductor (EGC). Most 2+G non-metallic-cables (NMC) are color coded for Black = "hot", White = neutral, and Bare = EGC
Disconnect it from the hard wired source and install a male plug on the fixture. Small blade is black hot, wider blade is white neutral.
What kind of plug? 120 Volt Alternating Currant non-grounded is black (hot) to narrow blade, white (neutral) to wide blade. Grounded has third prong, which is 'u' shaped, above and centered flat blades, which connects to the green (ground) wire. Be aware of currant loads, and use the proper gauge wire for the load. green&white wire to the top of plug, blue to the left, red to the right
No, the wide prong is neutral it is the white wire. The narrow prong is hot it is the black wire. The round prong (in a 3 wire plug) is safety ground it is the green wire.
The wide blade is the neutral and the narrow one is the hot.
The ground blade is the longest in a three blade plug.
Look at plug, wider blade is the Neutral (MARK IT) the more narrow blade is Hot (MARK IT) Cut end off wire.. Inside a wire splice box wire nut black to hot, white to neutral. This is a very basic task however if you have no experience maybe contact an electrician.
In North America the connections for a 15 amp cap (plug) goes as follows. Looking at the plug from the blade side directly on you should see a larger blade (silver) on the right, smaller (brass) blade on the left and a U shaped ground blade on the bottom. The white wire connects under the right (silver) coloured screw, the black wire connects under the left (brass) coloured screw and the green wire under the green ground screw.
An L5-30P is a two pole three wire grounding 30 amp, 125 volt plug . The neutral wire is connected to the W terminal, the ground wire to the G terminal and the hot wire to the only terminal that is left. The small blade/slot is neutral (white), the larger blade/slot is hot (black) and the notched blade/slot is ground (green).
To correctly wire a three-blade 220-volt plug, you should connect the hot wires (usually black and red) to the brass-colored screws, the neutral wire (usually white) to the silver-colored screw, and the ground wire (usually green or bare copper) to the green screw. Always make sure to follow the specific instructions provided by the plug's manufacturer and to disconnect power before working on any electrical connections.
you need a phono/mono plug to a 3.5mm jack. on the back of your amplifier, plug the red and white/black phono/mono plugs into the inputs commonly labelled aux. white/black into white/black and red into red. on the front of your amplifier, select aux and just plug and play.
The plug retrofit fits all original M50's which comes in black, white, and red.