0
What else can I help you with?
What electrons are responsible for the movement and storage of electrical charges?
Valence electrons are responsible for the movement of electrical charges in conductors. Electrons in the outermost energy level of an atom are free to move around and conduct electricity. Electrons can be stored in batteries as part of chemical reactions involving redox processes.
What is an electrical fault?
Some people will define the cause of an electrical fault as a "short circuit" but that is too simple an explanation because it doesn't explain how it is caused. An electrical fault is the name given to any situation where some electrical current goes where it was not intended to go. This situation can be caused by damage to the protective insulation around a wire - or around some other part - which puts the wire or part in contact with a different wire or part that it was not designed to touch because a difference in voltage has to exist between them to allow an item of electrical equipment to do its work. If an item of electrical equipment gets dropped accidentally - or if something else hits it violently - that action can easily damage the insulation material or close an air gap that was designed to keep two parts electrically separate within that item of equipment. Another way an electrical fault can be caused is by physical deterioration of some insulation. Such deterioration can be caused by many factors such as, for example, the temperature of the equipment being too high or if some unprotected equipment is exposed to wet or damp conditions. Such factors can put stresses on the insulation which it was not designed to withstand and it breaks down and causes an electrical fault to occur. If an item of electrical equipment (or an electrical wiring circuit which connects different pieces of equipment together) is properly designed, then, if an electrical fault occurs, protective circuit breakers should trip and/or fuses should blow to stop the flow of any excessive current that is the result of the electrical fault, thus helping to prevent any fires and/or explosions from happening because the fault occurred.
HOW MANY VOLTS ARE IN THE BATTERIES WE HAVE USED?
The small batteries (dry cells) used for many electronic devices usually have approximately 1.5 volts. Car batteries (which have several cells working in series) usually have around 12 volts. Other batteries may have other voltages.
Is the space around an electrical charged object is an electrical field?
yes
What is the flash protection boundary boundary?
The flash protection boundary (FPB) is a safety zone established around electrical equipment to protect individuals from the risks of arc flash incidents. It indicates the distance from the equipment within which a person could potentially receive a harmful level of thermal energy during an arc flash event. This boundary is calculated based on the available fault current, the duration of the arc, and the equipment's protective devices. Establishing the FPB is crucial for ensuring safe working conditions in environments where electrical hazards are present.
Is it a fine to work around disconnected batteries?
Yes, it is generally fine to work around disconnected batteries, as they do not pose an electrical hazard when properly disconnected. However, it is crucial to ensure that the battery terminals are insulated and that there is no risk of accidental reconnection. Always follow safety protocols and wear appropriate personal protective equipment to avoid any potential risks associated with battery handling.
Exterior electrical disconnect is required in sight of what?
It is usually expressed the other way around. The electrical disconnect has to be within 20 feet and line of sight of the equipment you are working on.
What is the primary objective of the Philippine electrical code?
As with every electrical code around the world, the primary objective is the safe installation of electrical equipment that is connected to the electrical grid. Overall the objective is keeping everyone and everything safe in conjunction with the use of an electrical supply source.
Does the Olympics increase pollution?
it will do with all the lights and electrical equipment and that. also all the people moving around trying to get to the olympics
What are the potential consequences of having a bad ground in an electrical system?
Having a bad ground in an electrical system can lead to electrical malfunctions, equipment damage, and even electrical fires. It can also pose a safety hazard to individuals working with or around the system.
Will welding be around in the next 10 years?
Certainly. And not only will it be around, the equipment used to do it will be more energy efficient and easier to control.
Where are insulators are used on electrical equipment?
Around all electric devices but most notably around conductors so that the electricity goes to where it is wanted to go.
What indicates why it is important to remove all jewelry before working around batteries?
Removing all jewelry before working around batteries is crucial because metal items can create short circuits, leading to sparks, fires, or even explosions in the presence of flammable gases emitted by batteries. Additionally, jewelry can conduct electricity, posing a risk of electrical shock or burns. Ensuring a safe working environment helps prevent accidents and injuries, making it essential to prioritize safety when handling batteries.
How can pressure control solenoid electrical d be solved?
Check the resistance across the terminals. Should be around 5 ohms.
Where can one find a tv remote that can handle different equipment around the house?
There are a variety of places to purchase a universal remote or a tv remote that can control different equipment around the house. Best Buy is a good place to buy electronics.
The kinds of ladders you avoid using around electrical equipment?
You want ladders that will not conduct electricity. Aluminum ladders are not a good idea. Fiberglass ladders are best for working around power cables.
How do you make a control panel to change the rotation of three phase induction motor?
The control panel will be based around a set of reversing magnetics. Depending on how you want to control the mags will depend on what type of peripheral equipment you will need to add to the control panel.
