0
You open the door on your microwave and it turned off completelywe checked all curcuit breakers and tried a different outlet its only 3 years old?
If the microwave turned off completely after you opened the door and you have already tried other outlets and circuit breakers, it could indicate a malfunction in the microwave's door sensor or control panel. It is advisable to have a professional technician inspect and repair the microwave. If it's only 3 years old, it might still be covered under warranty, so it's worth checking with the manufacturer.
What else can I help you with?
You have a small hole on the inside of the microwave door. is it dangerous?
A small hole on the inside of the microwave door is usually not dangerous as it is designed that way to allow steam to escape during cooking. However, it is important to check for any signs of damage or wear and tear on the door seal to ensure that the microwave functions properly and safely. If in doubt, it is best to have it checked by a professional.
Should a 20 amp circuit breaker get warm while in use?
Yes all breakers will get warm when in use. The full load current of the load flows through the device. Class A breakers current trip rating is rated at 40 degrees C. If in ambient temperatures higher that 40 C then the thermal trip rating lowers. Likewise if the ambient temperature becomes lower the trip rating increases. Sometimes breakers have to be rearranged in the electrical panel to keep high current breakers away from each other. The ambient temperature of adjacent breakers will raise a breakers temperature and cause needless tripping.
What circuit breaker will interchange with federal pacific?
There is no breaker that will fit a FPE panel except a FPE. The breakers are still being manufactured and are available at Lowes and Home Depot stores, but they are expensive. The failure rate of FPE breakers is worrisome and if I had one in my home I would change it. Federal Pacific has been out of business since the early 80's The current breakers being sold at Home Depot etc, are NOT manufactured by Federal Pacific since that company no longer exists. They are made by aftermarket companies. The FPE problems are not associated with the newer products, HOWEVER, there may be issues with the older FPE panels themselves. It is important to inspect the panels carefully and see that there are no burned or arcing areas and that all screws on the bus bar are securely tight and the bus is not damaged in any way. The breakers must fit properly and SECURELY in to the panel bus bar and the panel cover must hold the breakers securely in place as there are no actual screws to hold the breakers in place. If the breaker fit is loose or sloppy, there is a problem.To clarify the answer to the question, there ARE other options to Federal Pacific or the aftermarket manufactured products. Federal Pacific has a "sister" company in Canada called Federal Pioneer. They are still in business and still being installed today. Although there was a recall on some of there breakers several years ago, there is not the notorious history to Federal Pioneer and they have continued to improve on the product designs.The Federal Pioneer breakers are available in Canada at very competitive prices. There are some sellers on ebay as well, but the shipping costs may be a bit high if you order one or two breakers only.Federal Pioneer is marketed by Schneider Electric of Canada. Check online for further details on the products and availability. You can also buy US made breakers manufacturers like "American" "Challenger" and "Connecticut" electric and a few others. Old, used or NOS "Federal Pacific" breakers have been determined to have high failure rates and should not be used as replacements. Existing Federal pacific breakers should be replaced even if they "appear" to be functioning normally. Keep in mind that the Federal Pacific panels themselves may not meet current codes or standards and should not be used for new installations or "expansions". Replacements of existing breakers are usually "grandfathered" in but once again, the breaker panels themselves should be checked out thoroughly for damages and ALL screw connections should be tight and secure and breakers should be secure in the bus bar. Covers should be securely installed. It may not be cost effective to replace ALL breakers as opposed to replacing the entire breaker panel itself. Weigh out the costs carefully as well as the problems and costs of replacing the entire panel. Keep in mind your "future needs" when making this determination.
When your toaster and microwave are both running your 20 amp breaker trips Can you replace the 20 amp with a 30 amp breaker?
Definitely not, the 20 A circuit breaker is there to protect the wiring from becoming overheated. Any more current is potentially dangerous. The total power and current taken by the toaster and microwave should be checked to make sure that the 20 amp breaker is tripping correctly. It could be faulty. Both items should have a plate on the back, near where the power cord goes in, giving details. If the toaster and microwave together genuinely draw more than 20 amps you need a 30 amp circuit installed with the right wire size and a 30 amp breaker.
What else should you check if none of your outdoor outlets have electricity and none of the breakers on the main panel are tripped and you checked all GFCIs?
Is everything on that circuit breaker not working? Breakers will go bad sometimes. Get yourself an inexpensive receptacle tester (~$4.00 at hardware stores) and test each outlet. It looks like a plug with 3-4 lights on the end. It will diagnose simple problems (no hot, no ground, no neutral, reversed wires) and can aid in diagnosis.
Why do microwave ovens need to be regularly checked for safety?
they are regularly checked as microwaves can cook anything containing water, for example, your body cells.
Why do Microwave Ovens interfere with Satellite T V?
A microwave oven would interfere with you satellite TV do to the energy grenerated by the (klystron?) tube that generates the energy to cook the food. Howevr, that said, a your microwave should NOT interfere with your TV If it does, I would have the seals checked on your microwave, and would not stand near it when it is running.
Why does your heat pump keep blowing breakers?
There is a short somewhere. Probably the condenser fan motor or the compressor. Time to have it checked out by a competent, trusted techenician.
Who manufactures Cuisinart microwave oven?
Midea Microwave and Electrical Appliances MFG. Co., Ltd., a member of the Midea Group located in Beijiao, Foshan City, Guangdong, China. This information was obtained using the FCC ID located on the back of a Cuisinart Microwave and cross checked with the FCC Office of Engineering and Technology.
Are there any restrictions on bringing a microwave through airport security"?
Yes, there are restrictions on bringing a microwave through airport security. Microwaves are not allowed in carry-on luggage but can be packed in checked baggage. It is recommended to check with the airline for specific guidelines before traveling.
You have a small hole on the inside of the microwave door. is it dangerous?
A small hole on the inside of the microwave door is usually not dangerous as it is designed that way to allow steam to escape during cooking. However, it is important to check for any signs of damage or wear and tear on the door seal to ensure that the microwave functions properly and safely. If in doubt, it is best to have it checked by a professional.
How can you tell if a microwave is leaking radiation?
To test for microwave radiation leaks, you can place a phone inside the microwave, close the door, and call the phone from another device. If the phone inside rings or receives a call, there may be a leak. Additionally, you can use a microwave leakage detector to check for any radiation leakage. If you suspect a leak, it's important to stop using the microwave and have it checked by a professional.
Why 98 crv don't get electricity?
Nowhere near enough information is given in order to answer. Is the battery dead? Are the battery cables clean and tight? Have all the fuses and circuit breakers been checked? Is the ignition switch and/or the lights swtich broken?
Should a 20 amp circuit breaker get warm while in use?
Yes all breakers will get warm when in use. The full load current of the load flows through the device. Class A breakers current trip rating is rated at 40 degrees C. If in ambient temperatures higher that 40 C then the thermal trip rating lowers. Likewise if the ambient temperature becomes lower the trip rating increases. Sometimes breakers have to be rearranged in the electrical panel to keep high current breakers away from each other. The ambient temperature of adjacent breakers will raise a breakers temperature and cause needless tripping.
What is the size different between two testis in men?
i dont know but they should get it checked...
You have 91 camaro z 28 new battery new alt checked ground poscables the car will not charge battery what are you missing?
Check your fuses and circuit breakers. Could also be a bad ignition switch. Check your firewall connections for corrosion as well.
1999 Chrysler 300m tail lights do not work brake lights do work All fuses and breakers have been checked.?
Check the bulbs they are double filamented with larger used for tailights Could be a bad switch Check to see if you are getting power to the sockets
