It takes a finite amount of time to trip a breaker. The short you caused may not have tripped the breaker. If the dryer is no longer working there may be an internal reset that has tripped.
No, a breaker is designed to handle the load of only one circuit. Connecting two circuits to one breaker can overload the circuit and potentially lead to electrical hazards such as overheating, tripping the breaker, or causing a fire. Each circuit must have its own dedicated breaker.
To reset a breaker move the handle completely to the off position. If it had tripped you will feel a little resistance as it goes to the off position. If this doesn't restore the power the breaker is either bad and in need of replacement, or there is a persistent fault in the circuit causing the breaker to immediately re-trip. Breakers are safety devices.
A circuit breaker will trip if it is faulty or if the connected circuit has a short circuit or a connected device is trying to draw more current than the breaker rating. If you disconnect the output wire from the breaker and it still trips, it is a faulty breaker. If the breaker is tripping immediately when it is turned on then start disconnecting elements of the circuit to see what might be causing the problem. If everything was working and now isn't, it is likely that the wire from the breaker is nicked where it exits the box and is shorting to the feedthru connector.
Your only hope is that someone wired the box not to code and that there are two wires going into the offending breaker. If you can't separate wires you can't distribute the load.
A circuit breaker does not "cause" smoke. A circuit breaker "breaks" a circuit when there is too much current, creating a hazardous condition for the wires that are connected to the circuit breaker. The circuit breaker PROTECTS you from electrical fire. Find the source of the smoke; what burned? If a circuit breaker tripped during the incident, it is usually caused by melting/burning wire insulation, either inside or outside of an appliance. If the insulation inside the walls of your house has burned/melted, it could be that the circuit breaker was too large for the wire or that the circuit breaker failed to shut off at the appropriate current load. If the circuit breaker failed, your insurance should help you. If an appliance overloaded the circuit, your insurance should help you. If someone connected an oversized circuit breaker, causing the wire to overheat, your insurance company may refuse to help you.
No, a breaker is designed to handle the load of only one circuit. Connecting two circuits to one breaker can overload the circuit and potentially lead to electrical hazards such as overheating, tripping the breaker, or causing a fire. Each circuit must have its own dedicated breaker.
erosion is causing rocks to dissolve
The load current is greater that the amperage of the breaker. Add up everything that is plugged into the circuit. If the total is greater that the number marked on the handle of the breaker unplug some of the equipment.
To reset a breaker move the handle completely to the off position. If it had tripped you will feel a little resistance as it goes to the off position. If this doesn't restore the power the breaker is either bad and in need of replacement, or there is a persistent fault in the circuit causing the breaker to immediately re-trip. Breakers are safety devices.
you could have a loose connection causing it to arc enough to trip the breaker -- check all the connections -- maybe you'll need to change out the arc fault you could have a loose connection causing it to arc enough to trip the breaker -- check all the connections -- maybe you'll need to change out the arc fault
easy the changing of the weather
A circuit breaker will trip if it is faulty or if the connected circuit has a short circuit or a connected device is trying to draw more current than the breaker rating. If you disconnect the output wire from the breaker and it still trips, it is a faulty breaker. If the breaker is tripping immediately when it is turned on then start disconnecting elements of the circuit to see what might be causing the problem. If everything was working and now isn't, it is likely that the wire from the breaker is nicked where it exits the box and is shorting to the feedthru connector.
causing a neutral object to become charged by touching it with a charged object.
Your only hope is that someone wired the box not to code and that there are two wires going into the offending breaker. If you can't separate wires you can't distribute the load.
You can overload the circuit, causing a heavy load on the breaker. If the house wiring is old, it can build up heat, espeacially in an attic and create a "hot-spot" potentially causing a fire. Any microwave of 1,000 watts or larger needs to be on its own breaker. A curling iron or blowdryer can overload a circuit in your bathroom, and trip a breaker if it is being shared with other appliances on the same breaker. Always consult an electrician if your having troubles tripping breakers or blowing the older-style glass fuses in your house.
The breaker will blow because you are effectively causing a short circuit.
The only two ways to increase the speed of an object beyond its terminal velocity is to either reduce its drag, or increase the force causing it to fall. The speed of a falling object can be accelerated beyond terminal velocity, but absent a continuing force, and given enough time, it will eventually slow down to its terminal velocity.