1 ton = 12000 BTUs
voltage= f(ln(r)) graph is linear and voltage vs distance is non linear because voltage changes with 1/r so the graph is with curve. we use ln because ln direct the graph.
Do not use dangerous HCl or hydrochloric acid (muriatic acid) and go with a mixture of sodium chloride (salt ) and distilled water. Spray a mist evenly over the previously sandblasted Corten for a numbers of days while letting the surface dry between coats until the desired surface is achieved. This can take days or weeks depending on your environment. i.e. the Sahara vs the Amazon. You will need to sandblast first. The key to excellent results is the prep: use fine sand or 80 mesh aluminum oxide for the sandblasting. Keep dry and immediately start the pickling or patination process to insure an evenly rusted protective surface that is aesthetically pleasing.
This is not much of an answer but maybe helps to get started: First, the assumption is that the question is indeed about circular vs linear lists, as opposed to uni-directional vs bi-directional lists. A linear list is one that holds no valid, but in fact a designated invalid, value for the reference to the last item's successor, and the first item's predecessor. The name for this invalid reference value is subject to the implementation language, typically NULL, nil or nul. A circular list only uses valid reference values. Two forms of rings exist: the closed ring and the sentinel ring. The closed is one where the last item's successor references the first item, and the first item's predecessor refererences the last item. A characteristic feature of closed rings is that the algorithm cannot normally stop iterating on an "end reached" criterion. There will be different criteria, subject to the algorithm. A closed ring can never be empty, but it can go in and out of existence. A sentinel ring is one that contains one artificial element, the sentinel. This item acts as the anchor, as the last item's successor, and the first item's predecessor. A sentinel ring has the a well-defined start and stop (whenever iteration reaches the sentinel). The sentinel is an empty ring's only element. The reliable existence of the sentinel rids the ring of any invalid references; a useful aspect in the design of robust software. I argue that there is no superiority of one of these data structures over the over in the general case. All have their place; superiority or inferiority of a data structure must always be rated in context with the algorithm and data in mind.
This will depend if by bigger you mean having a larger payload, with the same amount of propellant, or it the payload is the same and only the mass of propellant changes. If you have more propellant/rocket fuel then the rocket will have more energy. The equation E=.5mv2 (e=energy, m=mass, and v=velocity) shows that if you have more energy then the velocity will increase. But if there is more mass then the velocity will be less. So the question is tough to answer with no set values as to the mass of the rocket fuel vs the mass of the payload. However if this is about rockets in space, where the net force acting on the rocket during the trip is effectively zero( no friction in space), then both rockets will go equally far, both will go indefinitely, with one just going faster than the other.
Coexisting technologies are distinct systems or technologies that operate side by side without interfering with one another. This concept is widely used to ensure that many technologies may coexist peacefully and function as intended in several industries, including networking, computers, and telecommunications.
Heating units are not measured in tons as AC units are. Heating capacity is referred to in 1000`s of btu output per hour of operation. The ratio of input vs output = the efficiency rating, for example if your home furnace is rated at 100,000 btu per hour input and 80,000 btu per hour output . it is 80% efficient (when it was new). For AC 12.000 btu = 1 ton.
Oil has the higher BTU rating Depends. If it is Liquified Nat. Gas then it has the higher rating.
G20 is a 3/4 ton and a G30 IS A 1 TON
The Way It Was - 1974 Joe Louis vs. Tony 'Two Ton' Galento was released on: USA: 29 January 1976
The number of BTUs (British Thermal Units) needed to heat a 2,400 sq ft is 80,650 BTU space depends on several factors, including: Key Factors Affecting BTU Requirements: Climate Zone (Cold vs. Moderate vs. Hot) Insulation Quality (Poor, Average, Excellent) Ceiling Height (Standard 8 ft vs. Higher) Number of Windows & Doors (More = More Heat Loss)
Of course you can. A ton or more of moving metal vs a person?
1030-1060 BTU/cf 1 gal (US) = 0.133 cf (cubic foot) 1 cf = 7.48 gal converting units, 138 - 142 BTU/gal X 600 ( the approximate volume change from liquid to gas = 84,000 BTU/galhttp://www.retailenergy.com/hybrid/Liquified%20Natural%20Gas.htm The previous answer neglected to account for the difference in the BTU/vol of methane as a liquid vs the BTU/vol of methane as a gas
Yes as he started his career with ever ton so he played with Liverpool.
Difference between cubic metric ton VS Metic ton , used for D.oil and F.oil in ShippingA shipping ton is 2,000 pounds, while a metric ton is 1,000 kilograms or about 2,200 pounds.
No, but the mounts themselves are different, and the 1979 may have an extra pair of mounts for the cab.
they all have approximately the same energy content -about 114,000 BTU/gal. varies somewhat depending on the fuel blend for differnent times of the year and area of the country, winter fuels a little less & summer fuels a little more
With heating oil at $2.89/gal and nat. gas at $1.61/ therm, using an 80% efficient oil vs: a 80% Nat gas heater, 1 million btu's cost you $27.00 for oil and $19.20 for nat. gas. Use applicable local pricing, convert to btu's per unit, etc. lc