The audio cable has nothing to do with DELAY. If you have delay, it is caused by something else.
Most modern televisions have at least a headphone output so even if there is no dedicated audio line output, the 3.5mm mini jack can be used to take the television output to an amplifier with just a little experimentation with the levels to be used. If there isn't even a headphone output, the other solution is to take the audio output from the video source itself. Satellite receivers, cable boxes and disc players usually have an audio line output. Each of the sources can be routed to the amplifier and bypass the television altogether. If this solution is chosen, there is a possibility that the audio may not be synchronized to to the vision. This is due to the signal processing that takes place between the video source and the image reaching the display itself. Most digital receivers and players have a menu setting to adjust the audio delay to overcome this. Look for menu selections called "audio sync" or "audio delay". This solution will work for all sources other than the tuners built in to the television. External receivers are the only solution for this. Note: There are solutions that involve adding wiring to the inside of the television. Televisions have potentially fatal voltages present inside them. Unless you are qualified, do not attempt any solution that involves taking apart any equipment.
Generally it isn't possible to send two video signals on a single wire although there are instances where it can happen. Video over Ethernet allows multiple signals to be sent in packets although the nature of Ethernet means that the signals will each have a delay so synchronizing the signals may be difficult. Video over CAT5 uses converters that take a video signal and modify it to run over a single pair of a CAT5 cable. Normally, two more pairs would be used for stereo audio. If mono audio is used, it is possible to run two composite video signals with audio down one cable. Note that video over CAT5 uses the same cable as Ethernet but employs a very different signal format to Ethernet. Composite video signals use a single cable but in fact, the signal has three separate video components encoded into the signal. The signals are one for brightness and two for color information. Together they make up a full color signal and can be separated into the three components at the far end. Although the cable carries three signals, remember that they are all parts of the same color signal so this probably doesn't qualify as two signals. Finally, cable broadcasters use encoding systems to allow numerous signals to be carried on a single cable. The one that enters a house to supply a cable receiver carries many signals with just one being decoded and output by the receiver. This takes complex hardware at both ends so is outside the scope of most home users.
Time delay relayA relay which responds to a signal with a certain delay. In some ignition systems, a time delay relay allows for full vacuum advance 20-30 seconds after start-up, after which control is again taken up by the TCS; some cars have an additional time delay relay which delays vacuum advance about 30 seconds after the transmission has been shifted to high gear
She pretends to die.
He does not want to tell Oedipus the painful truth.
Audio cables don't cause delays.
An audio cable alone can not cause a DELAY in the sound. We're not into answering test questions here. That is cheating. This question has been asked several times.
In-phase.
To achieve a delay after reverb effect in your audio production, you can apply a delay effect to the reverb signal. This will create a sense of space and depth in your audio by adding a delayed echo to the reverberated sound. Adjust the timing and feedback settings of the delay effect to control the length and intensity of the delay.
To achieve a delay before or after reverb in your audio production, you can use a digital audio workstation (DAW) with plugins that allow you to apply delay and reverb effects separately. Simply insert a delay effect before or after the reverb effect in the audio chain to create the desired effect. Adjust the settings of each effect to control the timing and intensity of the delay and reverb.
A delay before distortion in audio signals can be caused by factors such as signal processing, filtering, or the limitations of the equipment used to capture or reproduce the audio.
A delay pedal is an audio effect used in music to play back a sound created and then stored into an audio storage medium. The sound can be played back once, or multiple times. The delay pedal can add texture to music.
Adding a delay before reverb in audio production can create a sense of depth and spaciousness in the sound. It can make the audio feel more immersive and natural, enhancing the overall quality of the mix.
You use it as a send or as an insert.
Another word for "without delay" is immediately.
Some T.V.s have audio lag, most of the time you can adjust this.
Reverb and delay are both audio effects used in production. Reverb creates a sense of space and depth, while delay repeats the sound with a time delay. Using reverb before delay can enhance the mix by creating a more natural and cohesive sound, as the reverb provides a sense of space for the delayed sound to exist in. This can result in a more immersive and polished overall sound quality.