If you have access to a multi-meter, do a resistance check from end to end on each core while the cable is disconnected. You should have close to 0 ohms on both cores. Do a resistance check between the cores, while the cable is disconnected. You should have an open circuit between the two. Alternatively, connect one end to an amplifier, the other to a speaker and listen for sound. If nothing is heard, substitute the cable, then the speaker and finally the amplifier to establish where the fault is.
It is better to use 16 gauge or 14 gauge speaker wire for your home theater applications.
Yes; it is tinned copper.
Whichever one you connect to the positive terminal. The colors are there so you can find the same wire at the other end.
The same as with any other speaker wire. Monster Cable is a brand name, but it may require a special set of connectors to adapt to your system depending on the size of wire you purchase. Remember, there is such a thing as overkill when making your purchase and sometimes all isn't as impressive as it's advertised.
Hi, That's your speaker protector system. When something's not right (usually a shorted speaker wire) or the speaker itself is defective, it senses it and stops the receiver from applying power to the speakers to keep it from burning out the power amplifiers. Hope that helps, Cubby FROM DarthMurdicide: The absolute easiest way to find out if it is a wiring problem without having to disconnect and reconnect wiring on the backs of the speakers or the receiver is to use the TEST TONE function to test the individual speakers. It is a tone that to me is not stressful to the speakers, so I put the volume to MAX for the test and check each individual speaker. If it is a wiring problem, when you get to the speaker that is either blown or the wiring is grounded out somewhere (either at the back of the speaker or the back of the receiver, or somewhere in between), the PROTECTOR message will light up. I verified this procedure last night. I did the TEST TONE's for each individual speaker on MAX volume, and sure enough when I got to the surrond back left speaker, the PROTECTOR mesage came on. I pulled the in-wall speaker out, and sure enough the tweeter wiring terminal had been bent back during installation and was touching the crossover cap, causing a short. I bent it back, and voila, no more PROTECTOR message.
Observe polarity and touch a 1.5 volt battery to the terminals and note the direction the speaker cone moves.
The positive speaker wire is a solid color, your negative wire should have a stripe on it.
2006 Mazda 6 Car Stereo Radio Wiring Diagram Radio Constant 12V+ Wire: Blue/RedRadio Switched Ignition 12V+ Wire: OrangeRadio Ground Wire: BlackRadio Illumination Dimmer Wire: Light Green/RedRadio Antenna Trigger Wire: N/ARadio Amplifier Turn On Wire: Blue/BlackFront Speaker Size: N/AFront Speaker Location: N/ALeft Front Speaker Wire (+): RedLeft Front Speaker Wire (-): WhiteRight Front Speaker Wire (+): BlueRight Front Speaker Wire (-): YellowRear Speaker Size: N/ARear Speaker Location: N/ALeft Rear Speaker Wire (+): PurpleLeft Rear Speaker Wire (-): PinkRight Rear Speaker Wire (+): White/BlueRight Rear Speaker Wire (-): Black/Blue
Battery Constant 12v+ Wire: WhiteAccessory Switched 12v+ Wire: White/BlackGround Wire: BlackIllumination Wire: Red/YellowDimmer Wire: Red/GreenAntenna Trigger Wire: PinkLeft Front Speaker Positive Wire (+): WhiteLeft Front Speaker Negative Wire (-): Black/BlueRight Front Speaker Positive Wire (+): BlueRight Front Speaker Negative Wire (-): White/RedLeft Rear Speaker Positive Wire (+): Light GreenLeft Rear Speaker Negative Wire (-): Light Green/BlackRight Rear Speaker Positive Wire (+): GrayRight Rear Speaker Negative Wire (-): Gray/Black
In a 1994 Corolla, the radio battery constant 12v+ wire is blue/yellow, the radio accessory switched 12v+ wire is gray, the ground wire is brown, and the illumination wire is green. For the front speakers, the left front speaker wire (+) is pink, the left front speaker wire (-) is violet, the right front speaker wire (+) is light green, and the right front speaker wire (-) is blue. For the rear speakers, the left rear speaker wire (+) is black, the left rear speaker wire (-) is yellow, the right rear speaker wire (+) is red, and the right rear speaker wire (-) is white.
1998 Toyota Tacoma Stereo Wiring InformationRadio Battery Constant 12v+ Wire: Blue/YellowRadio Accessory Switched 12v+ Wire: GrayRadio Ground Wire: BrownRadio Illumination Wire: GreenLeft Front Speaker Positive Wire (+): PinkLeft Front Speaker Negative Wire (-): PurpleRight Front Speaker Positive Wire (+): GreenRight Front Speaker Negative Wire (-): BlueLeft Rear Speaker Positive Wire (+): BlackLeft Rear Speaker Negative Wire (-): YellowRight Rear Speaker Positive Wire (+): RedRight Rear Speaker Negative Wire (-): White
For the front speakers in a 1993 Ford Ranger pickup truck, the left front speaker wire (+) is orange/green, the left front speaker wire (-) is black/white, the right front speaker wire (+) is white/green, and the right front speaker wire (-) is black/white. For the rear speakers, the left rear speaker wire (+) is pink/green, the left front speaker wire (-) is pink/blue, the right rear speaker wire (+) is pink/blue, and the rear right speaker wire (-) is green/orange.
Constant 12V+ Wire: Light Green Ignition Switched 12V+ Wire: Black/Yellow Ground Wire: Black Illumination Wire: Blue/Yellow Dimmer Wire: N/A Left Front Speaker Wire (+): Green Left Front Speaker Wire (-): Blue/Red Right Front Speaker Wire (+): Light Green/Yellow Right Front Speaker Wire (-): Black/Green Left Rear Speaker Wire (+): Green/Yellow Left Rear Speaker Wire (-): Blue/Orange Right Rear Speaker Wire (+): Green/White Right Rear Speaker Wire (-): Green/Blue
Radio Constant 12V+ Wire: Blue/Yellow Radio Switched 12V+ Wire: Gray Radio Ground Wire: Brown Radio Illumination Wire: Dark Green Dimmer Wire: White/Green Antenna Trigger Wire: None Front Speaker Size: 6 1/2″ Front Speaker Location: Doors Left Front Speaker Wire (+): Pink Left Front Speaker Wire (-): Purple Right Front Speaker Wire (+): Green Right Front Speaker Wire (-): Blue Rear Speaker Size: 6″ x 9″ Rear Speaker Location: Rear Deck Left Rear Speaker Wire (+): Black Left Rear Speaker Wire (-): Yellow Right Rear Speaker Wire (+): Red Right Rear Speaker Wire (-): White
1997 Toyota Tercel Car Stereo Radio Wiring Diagram Radio Constant 12V+ Wire: Blue/YellowRadio Switched 12V+ Wire: GrayRadio Ground Wire: BrownRadio Illumination Wire: GreenRadio Dimmer Wire: N/ARadio Power Antenna Trigger Wire: Black/RedRadio Amplifier Turn On Trigger Wire: N/AFront Speakers Size: 4″Front Speakers Location: DoorsLeft Front Speaker Wire (+): PinkLeft Front Speaker Wire (-): PurpleRight Front Speaker Wire (+): Light GreenRight Front Speaker Wire (-): BlueRear Speakers Size: 6 1/2″Rear Speakers Location: Side PanelsLeft Rear Speaker Wire (+): BlackLeft Rear Speaker Wire (-): YellowRight Rear Speaker Wire (+): RedRight Rear Speaker Wire (-): White
it could also be a bad preamp or whatever there called inside the place were the speaker goes... run test leads(2) directly from the rear of the radio (at the right speaker lead)to the speaker itself. If the speaker now works you have a broken wire in the harness. It is easier to run new speaker leads than try to locate the break. This seems to be a problem with Cherokees.
The color of speaker wire doesn't matter, it's what it's made of. Also, expensive speaker wire is a rip off. You should just buy cheap speaker wires and that's good.