Not generally no. There would be no point. The easiest is to convert the standard yellow video out to coax with an RF modulator
They are both color space video but PrPbY is analog video and CrCbY is digital video.TriviaConventionally the Y is first followed by b then r, as in YPbPr which has led to the wires being known as 'yipper' lines/cables.
Y Pb Pr cables are identical to those used for YUV, Y Cb Cr and RGB cables. They are therefore completely interchangeable. YUV and YPbPr signals are both referred to as component signals although the precise format of the signals are different. The interface is the same for each, namely three wires. The standard cable is a 75 Ohm co-ax cable terminated in RCA plugs for domestic equipment and BNC connectors for commercial equipment. It is always worth using good quality cable to avoid losses in the signal. RGB uses the same three wires but the signal is separated into three separate colors. Normally, an RGB signal will have additional cables for synchronisation signals so an RGB interface will often have 4 or 5 connectors.
Most laptops are now equipped with a DisplayPort interface (or similar) which, with the correct adapter, may be connected to televisions with an HDMI or DVI interface. Older laptops may have an S-Video connection (analogue audio/video), or simply a DVI port. If your television has an S-Video port, you may use this for standard definition audio/video. Alternatively, using an adapter, the DVI port may be connected via the HDMI interface on a newer television. When using a DVI connection, you must provide an alternative connection for audio, as unlike HDMI, DVI does not carry audio. This can be problematic when using a DVI-to-HDMI adapter, as most consumer televisions provide no way to map separate audio and video sources to the same channels, or for mixing analogue and digital sources. Some televisions also include VGA connections, though they do not tend to provide high-definition output (despite VGA having more than adequate bandwidth) as they expect XGA standard input (1024x768). If a VGA interface is available on your television, there will normally be an audio jack interface for audio too. DVI-I ports on computer equipment provide piggy-backed analogue connectivity (unlike digital-only DVI-D interfaces) via a DVI-to-VGA adapter. To determine which type of interface is provided should be as simple as looking at the port. If the port includes a cross-shaped 'hole' (i.e- if it looks like [+::::::] ), it is usually DVI-I, though some cheaper graphics cards manufacturers have been known to use the DVI-I port on a DVI-D interface, possibly in order to trick consumers into buying an inferior product. If it is more like a hyphen ( [ - ::::::] ), it is definitely DVI-D and can only be connected to a digital interface (such as DVI or HDMI).
Coaxial adapters for YPBPR cable can be found at most Radio Shack stores. This type of cable in VGA and Audio to HDMI conversions.?æ
To get sound from YPbPr (component) cables, you will need a separate audio connection such as analog audio cables or an audio extractor that combines the audio signal into the same cable as the video. YPbPr cables only carry video signals, so you must use a separate audio connection to transmit sound to your audio device.
I dont believe it is. YBbPr is capable of outputting High definition (1080) where as S-video is Standard Definition
As rf modulators are usually mains powered convention says the standard cabling is easier to get
RGB, YPbPr is characterized by having three RCA plugs at each end.
There are no dedicated PC inputs in the rear of this Alba LCDW16HDF model. There are, however, an HDMI, a SCART connector, Component Audio/Video Inputs (YPbPr), a S/PDIF input (digital audio input), an RF Input to connect to an antenna or a coaxial cable, and finally, there are stereo audio line outs. The HDMI input is compatible with the DVI outputs found on more modern PCs-all that is required is a simple pin adapter. Picture quality can be excellent via this method.
There should be a little square hole at the end that plugs into the Xbox 360. This is for an optical audio cable that hooks to a surround amp.
Nintendo released a component (YPbPr) cable when the GameCube launched, but quickly stopped supporting it. Newer consoles don't have the "Digital A/V Out" port at all. If you have one of the original models with that port, you can try to track down the component video cable, although they tend to be rather expensive since there weren't many made. There are no cheaper, third-party alternatives for this cable. To when connecting the system to your TV, you will also need the original composite (yellow/red/white) cable for the RL audio, since the component cable does not have its own audio plugs. There will be no lag if the system is connected to the TV with these cables.
YPbPr is an analog component video signal that splits the video signal into three separate components: Y for brightness (luma), Pb for the difference between blue and luma, and Pr for the difference between red and luma. This signal is commonly used for transmitting high-definition video signals.
Al = Audio Left Ar = Audio Right Y = Luma Pb = the difference between Blue and Luma Pr = the difference between Red and Luma YPbPr is converted from RGB (RedGreenBlue) signal. There is no Green signal needed, it is interpolated from the Luma, Blue and Red signal.
Y Pb Pr is a form of component video with three signals. Y is the brightness signal while Pb and Pr each carry color information. All three are required to produce a full color image and they do not carry audio. Audio will usually require a further two connectors for stereo audio.
They are both color space video but PrPbY is analog video and CrCbY is digital video.TriviaConventionally the Y is first followed by b then r, as in YPbPr which has led to the wires being known as 'yipper' lines/cables.