Creon thinks the Sentry has buried the body of Polynices.
He orders the sentry to find out who is burying polyneices because he had strict orders to not bury him. Then the sentry brings Creon's niece Antigone in and sentences her to death.
The military term 'sentry' typically refers to a person who is standing guard at an installation entry point. Examples are military police, security forces, and security police. Other terms used to describe a sentry are gate guard and entry controller.
Because the guards saw her burying the body and Creon told the sentry to figure out who had buried the body and defied his orders or the sentry would be the one serving the death penalty.
The sentry captured Antigone burying Polyneices and brought her to Creon
(1) The first step of course is to acquire a blank transponder key. These can be purchased from your Jeep dealer or bought online. Online prices are usually around $20.00. You can then take the blank key along with one of your original keys to any key maker or locksmith and have it cut to match, just like with any other key. (2) Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the On position. (3) After the ignition switch has been in the On position for longer than three seconds, but no more than fifteen seconds, cycle the ignition switch back to the Off position. Replace the first valid Sentry Key in the ignition switch lock cylinder with the second valid Sentry Key and turn the ignition switch back to the On position. The second valid Sentry Key must be inserted in the lock cylinder within fifteen seconds of removing the first valid key. (4) About ten seconds after the completion of Step 3, the SKIS indicator in the instrument cluster will start to flash and a single audible chime tone will sound to indicate that the system has entered the Customer Learn programming mode. (5) Within sixty seconds of entering the Customer Learn programming mode, turn the ignition switch to the Off position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the On position. (6) About ten seconds after the completion of Step 5, a single audible chime tone will sound and the SKIS indicator will stop flashing, stay on solid for three seconds, then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKIS will immediately exit the Customer Learn programming mode and the vehicle may now be started using the newly programmed valid Sentry Key. Each of these steps must be repeated and completed in their entirety for each additional Sentry Key that is to be programmed. If the above steps are not completed in the given sequence, or within the allotted time, the SKIS will exit the Customer Learn programming mode and the programming will be unsuccessful. The SKIS will also automatically exit the Customer Learn programming mode if it sees a non-blank Sentry Key transponder when it should see a blank, if it has already programmed eight (8) valid Sentry Keys, or if the ignition switch is turned to the Off position for more than about fifty seconds. NOTE: If an attempt is made to start the vehicle while in the Customer Learn mode (SKIS indicator flashing), the SKIS will respond as though the vehicle were being started with an invalid key. In other words, the engine will stall after about two seconds of operation. NOTE: Once a Sentry Key has been programmed as a valid key to a vehicle, it cannot be programmed as a valid key for use on any other vehicle.
If the key has the built in remote buttons, it has sentry key.
The red dot is an indicator for a failure in the theft/sentry key system. The sentry key system is for the key with "chips" in them.The red dot is an indicator for a failure in the theft/sentry key system. The sentry key system is for the key with "chips" in them.
A failure in the Sentry Key system (chipped key)A failure in the Sentry Key system (chipped key)
No, the sentry key (skim) is a learned function that can not be removed.No, the sentry key (skim) is a learned function that can not be removed.
A malfunction of the Sentry Key system (key with a theft chip in it)A malfunction of the Sentry Key system (key with a theft chip in it)
The instructions on in the book that came with the van. Customer Key Programming You can program new sentry keys to the system if you have two valid sentry keys by performing the following procedure: 1. Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code. 2. Insert the first valid key into the ignition switch and turn the ignition switch ON for at least 3 seconds but no longer than 15 seconds. Turn the ignition switch OFF and remove the first key. 3. Insert the second valid key and turn the ignition switch ON within 15 seconds. After ten seconds a chime will sound and the Theft Alarm Light will begin to flash. Turn the ignition switch OFF and remove the second key.
On a Chrysler vehicle with sentry key (chip key), you just have to put the key in the ignition and turn it on.On a Chrysler vehicle with sentry key (chip key), you just have to put the key in the ignition and turn it on.
It is Part of the Sentry Key Computer and instrument cluster. The Sentry Key Computer is located on the steering column around the key cylinder.
You can program new keys to the system if you have two valid sentry keys by performing the following procedure: # Cut the additional Sentry Key Transponder blank(s) to match the ignition switch lock cylinder key code # Insert the first valid key into the ignition switch and turn the ignition switch ON for at least 3 seconds but no longer than 15 seconds. Turn the ignition switch OFF and remove the first key. # Insert the second valid key and turn the ignition switch ON within 15 seconds. After ten seconds a chime will sound and the Theft Alarm Light will begin to flash. Turn the ignition switch OFF and remove the second key. # Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry key has been programmed. Repeat this procedure to program up to a total of 8 keys. If you do not have a programmed sentry key, contact your dealer for information.
A red circle warning light is an indication of a malfunction in the theft alarm or Sentry key (chip key) system.A red circle warning light is an indication of a malfunction in the theft alarm or Sentry key (chip key) system.
Engine, trans, and abs are under the hood. Airbag, cluster, body, sentry key (chip key), hvac, and compass are inside.Engine, trans, and abs are under the hood. Airbag, cluster, body, sentry key (chip key), hvac, and compass are inside.