answersLogoWhite

0

200 lbs per sqft

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How much dead load can an 8' 2x6 hold lying flat Given that it is supported at each end flush with vertical 2x6's at 60 degrees There are 2 Load Bearing points 8 inside each support?

The dead load capacity of an 8' 2x6 lying flat can vary based on factors such as the type of wood, spacing, and load distribution. Typically, a 2x6 can support roughly 40-50 pounds per linear foot when properly supported. Given the specific configuration of the supports and load bearing points, you can expect the 8' 2x6 to hold approximately 320-400 pounds total, but it's essential to consult with structural engineering guidelines for precise calculations. Always consider safety factors and local building codes when determining load capacities.


What is the recommended span for a 2x6 board?

The recommended span for a 2x6 board is typically around 8 to 12 feet, depending on the load it needs to support.


What is the maximum weight capacity for a 2x6 span?

The maximum weight capacity for a 2x6 span is typically around 50 pounds per square foot, but it can vary depending on the type of wood and the length of the span.


Will a w-8x18 carry the weight of a basement load wall 2x6 over a 20 ft span?

Yes, a W-8X18 will carry the weight of a basement load wall 2X6 over a 200 feet span.


How much can a 12 foot 2x6 board on edge support?

The load-bearing capacity of a 12-foot 2x6 board on edge depends on several factors, including the type of wood, the spacing of supports, and the load distribution. Generally, a 2x6 made from common softwoods like pine can support approximately 1,000 to 1,500 pounds when properly supported at both ends and loaded uniformly. However, for safety and structural integrity, it's essential to consult local building codes or a structural engineer for specific applications.


How far can a 2x6 span without support?

A 2x6 board can span up to 9 feet without support, depending on the type of wood and the load it needs to bear.


How far will a 2x6 span without support?

A 2x6 board can span up to 9 feet without support, depending on the type of wood and the load it needs to bear.


What is the maximum span for a 2x6 beam?

The maximum span for a 2x6 beam is typically around 10-15 feet, depending on the load it needs to support and the building codes in place.


What is the difference between a 2x4 and 2x6 piece of wood?

The primary difference between a 2x4 and a 2x6 piece of wood is their dimensions; a 2x4 measures approximately 1.5 inches by 3.5 inches, while a 2x6 measures about 1.5 inches by 5.5 inches. This difference in width provides the 2x6 with greater strength and load-bearing capacity, making it suitable for structural applications where more support is needed. Additionally, the choice between the two often depends on the specific requirements of a project, such as insulation space or aesthetic considerations.


What is the load capacity of a Mazda truck?

The load capacity is usually listed on the vehicle title. Load capacity ratings are 1/2 ton, 3/4 ton, etc.


Why is it that when the load exceeds the network capacity delay tends to infinity?

As load exceeds network capacity, packets gets jammed at nodes. These packets never go forward unless load goes below network capacity. Hence when load exceeds network capacity delay tends to infinity. As load exceeds network capacity, packets gets jammed at nodes. These packets never go forward unless load goes below network capacity. Hence when load exceeds network capacity delay tends to infinity.


Can a lift truck with a 6000 lb capacity at 24 load center lift the load below with 30 load center?

No, a lift truck with a 6000 lb capacity at a 24-inch load center cannot safely lift a load with a 30-inch load center. The capacity of a lift truck decreases as the load center increases, meaning that the effective lifting capacity at a 30-inch load center would be lower than 6000 lbs. It's important to refer to the lift truck's load capacity chart to determine the specific capacity at different load centers.