The acronym PSI stands for "Pounds per Square Inch," and is the common unit of measurement for pressure. It can be understood as the amount of force that is exerted on an area of one square inch. Normal atmospheric pressure at sea level is 14.7 PSI The acronym PSI stands for "Pounds per Square Inch," and is the common unit of measurement for pressure. It can be understood as the amount of force that is exerted on an area of one square inch. Normal atmospheric pressure at sea level is 14.7 PSI
No. A pound is a unit of force, and PSI is for pressure and stress. 1 PSI is one pound of force distributed over 1 square inch of area. 1 PSI could also be 2 pounds distributed over 2 square inches, etc.
psi and pounds do not covert over, pounds are a measure of weight, psi is a measure of pressure. 1psi means the pressure contained is applying a force of 1pound per square inch of its surrounding container
PSI = Pounds Per square inch
The pressure does not have an inherent weight it is simply applying a force.
There can be no conversion. 1000 lbs is a measure of mass. That can be stretched to a measure of force (weight) if your knowledge of basic physics is very poor. On the other hand psi is a measure force per unit area (psi = pounds per square inch). The two are based on different measurement units and according to the most basic principles of dimensional analysis, any attempt at conversion between the two is totally flawed.
pounds and pounds/in2 are two different units.
1 Pound over an area of 1 square inch.
There can be aby number of psi in a cubic foot because psi is a measurement of pressure and the gas can be any pressure you care to make it.
1 litre diesel in joules
For your information, Bar is the atmospheric pressure at the sea level, which equals to 100 kilopascals. Psi is 1 pound of force per square inch. You may use this pressure conversion table if you are converting from bar to psi (pound per square inch) for the values listed in the table below.1 Bar = 14.5037738 Psi (Pound Per Square Inch)
You cannot convert "Newton meters" to psi. psi is a pressure and "newton per square meter" is also a pressure that is called pascal (Pa). Here is a fine pressure converter: Scroll down to related links and look at "Conversion of pressure or stress units".
1psi = 0.068 atm. So to convert 30 psi using dimensional analysis... 30 psi x 0.068 atm/1 psi = 2.04 atm
Pound per Square Inch = PSI means 1pound in terms of pressure will be 1 psi.
You can lift a locomotive or a house with 1 psi, if the pressure is applied over a large enough area.
Your question is not answerable. PSi is a measure of force or pressure. Cubic feet is a measure of volume.
psi is equal to psig...if psi is in the pressure gauge or psig..on a gauge
about 2350 psi or 16.2 MPa
1 kg/sq cm = 14.2233 psi 140 kg.sq cm = 140 x 14.2233 psi = 1991.262 psi
That's really not answerable w/o a lot of assumptions. There's a unit of pressure called PSI, which stands for Pounds-per-Square-Inch. If you have 1 PSI, applied over 8,4 square inches(or more), you will lift one gallon of water.
The pressure of liquid acting on a container or other body increases at the rate of 1 atmosphere or about 14.7 lbs. per square inch for every increase of 33 feet in depth. So doing the math results in: 400ft./33ft. = 12.121. Multiplying that by 14.7 lbs. per square inch yields about 178 lbs. per square inch at 400 feet deep.
No more then a 1/2 PSI
Pounds per Square Inch or Psi is a unit of pressure or stress. 1 bar is equal to 14.50377 Psi.
There can be aby number of psi in a cubic foot because psi is a measurement of pressure and the gas can be any pressure you care to make it.
1 bar = 14.7 psi therefore 9 bar = 132.3 psi