answersLogoWhite

0

The frequency of the wave is the reciprocal of its period. Therefore, the frequency of a wave with a period of 9.26 ns is approximately 108 MHz (1 / 9.26 x 10^-9 seconds = 108 x 10^6 Hz).

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Physics

What is the period of a wave whose frequency is 2MHz?

The period is the reciprocal of the frequency. 1 / 2 million Hz = 500 ns or 0.5 us (microseconds).


What is the relationship between wavelength and frequency?

Wavelength, λ, and Frequency, f, are inversely proportional. Their product is a constant, the wave velocity. For lightwaves, their product is the speed of light, c: c = λ * f = 299,792,458 m/s, ~= 3.00 * 10**8 m/s, 0.300 m/ns, 30.0 cm/ns, ~= 186,000 mi/s, 11.811 in/ns, 0.984252 ft/ns; Where ns = nanoseconds, or 10**-9 seconds. Frequency, f, and Wavelength, λ, describe simple values that can be measured on a moving wave, if it contains a constant signal or, at least, a clearly repetitive waveform. So, as the wave moves past a reference point like a microphone, or radio receiver, find some repetition in the wave, measure the shortest interval of time, t, that marks the entire repetition. The frequency, f, is simply[1] the reciprocal of that time interval: f = 1 / t The wavelength is the measured distance between two identical areas of the waveform (like peaks, troughs, or blips), in adjacent copies of a repeating waveform. Whereas the interval measurements required one wave sensor, plus a fast timer, the wavelength measurements require two wave sensors, accurate distance measurements, but no timer. As the sensors are separated, the two signals will diverge until, at one wavelength separation, the two signals become identical again (difference is minimal). Sometimes, it is hard to be highly accurate about where, exactly, a single interval starts and stops. However, if you can flawlessly count a large number of repetitions, just do your best to start and stop the timer in the same place on the first and last repetition. Now you get to multiply your accuracy! Divide the total time, Δt, by the number of intervals, n, this average is an improved measurement of interval! t = Δt / n If you divide the count by the time interval, you get an improved frequency measurement. [1] Frequency is a counted number, n, of full waveform repetitions divided by the total elapsed time, Δt. f = n / Δt


How many ns are in 1 second?

The prefix nano (n) means 10-9 of something, in this case 1 ns are equivalent to 10-9 s. So 1 second is composed by 109 ns.


What is the conversion factor from kilograms per meter per second (kg/ms) to nanoseconds per square meter (ns/m2)?

To convert from kilograms per meter per second (kg/ms) to nanoseconds per square meter (ns/m2), the conversion factor is 1 kg/ms 1,000,000,000 ns/m2.


How many nanoseconds are in second?

1 ns (nanosecond) = 10-9s 1s / 10-9s = 109 109 = 1000 000 000 1 second = 1000 000 000 ns (nanosecond)

Related Questions

What is the period of a wave whose frequency is 2MHz?

The period is the reciprocal of the frequency. 1 / 2 million Hz = 500 ns or 0.5 us (microseconds).


What is the speed in terms of Mhz of a clock period of 1 ns?

A clock with a period of 1 ns has a frequency of 1 GHz, or 1000 MHz.


What is the period of a 1GHz sine wave?

The period of 1GHz is 1 ns. The waveform is irrelevant.


What is the period of a 15MHz sine wave?

The period of a 15MHz sine wave is 1 / 15MHz, or 0.066667 us, or 66 2/3 ns.


Give the clock out frequency and state time T of 8085 when the crystal frequencies is 5MHz?

The clock out frequency of an 8085 is one half the crystal frequency. The period of one T cycle is the inverse of the clock frequency. At a crystal frequency of 5MHz, the clock is 2.5MHz, and T is 400 ns.


What is the relationship between wavelength and frequency?

Wavelength, λ, and Frequency, f, are inversely proportional. Their product is a constant, the wave velocity. For lightwaves, their product is the speed of light, c: c = λ * f = 299,792,458 m/s, ~= 3.00 * 10**8 m/s, 0.300 m/ns, 30.0 cm/ns, ~= 186,000 mi/s, 11.811 in/ns, 0.984252 ft/ns; Where ns = nanoseconds, or 10**-9 seconds. Frequency, f, and Wavelength, λ, describe simple values that can be measured on a moving wave, if it contains a constant signal or, at least, a clearly repetitive waveform. So, as the wave moves past a reference point like a microphone, or radio receiver, find some repetition in the wave, measure the shortest interval of time, t, that marks the entire repetition. The frequency, f, is simply[1] the reciprocal of that time interval: f = 1 / t The wavelength is the measured distance between two identical areas of the waveform (like peaks, troughs, or blips), in adjacent copies of a repeating waveform. Whereas the interval measurements required one wave sensor, plus a fast timer, the wavelength measurements require two wave sensors, accurate distance measurements, but no timer. As the sensors are separated, the two signals will diverge until, at one wavelength separation, the two signals become identical again (difference is minimal). Sometimes, it is hard to be highly accurate about where, exactly, a single interval starts and stops. However, if you can flawlessly count a large number of repetitions, just do your best to start and stop the timer in the same place on the first and last repetition. Now you get to multiply your accuracy! Divide the total time, Δt, by the number of intervals, n, this average is an improved measurement of interval! t = Δt / n If you divide the count by the time interval, you get an improved frequency measurement. [1] Frequency is a counted number, n, of full waveform repetitions divided by the total elapsed time, Δt. f = n / Δt


Nanoseconds is the period of the cesium-133 radiation used to define the second?

1,087,827,757 ns


What is (-3) and divide(-2) plus 8?

Wavelength, λ, and Frequency, f, are inversely proportional. Their product is a constant, the wave velocity. For lightwaves, their product is the speed of light, c: c = λ * f = 299,792,458 m/s, ~= 3.00 * 10**8 m/s, 0.300 m/ns, 30.0 cm/ns, ~= 186,000 mi/s, 11.811 in/ns, 0.984252 ft/ns; Where ns = nanoseconds, or 10**-9 seconds. Frequency, f, and Wavelength, λ, describe simple values that can be measured on a moving wave, if it contains a constant signal or, at least, a clearly repetitive waveform. So, as the wave moves past a reference point like a microphone, or radio receiver, find some repetition in the wave, measure the shortest interval of time, t, that marks the entire repetition. The frequency, f, is simply[1] the reciprocal of that time interval: f = 1 / t The wavelength is the measured distance between two identical areas of the waveform (like peaks, troughs, or blips), in adjacent copies of a repeating waveform. Whereas the interval measurements required one wave sensor, plus a fast timer, the wavelength measurements require two wave sensors, accurate distance measurements, but no timer. As the sensors are separated, the two signals will diverge until, at one wavelength separation, the two signals become identical again (difference is minimal). Sometimes, it is hard to be highly accurate about where, exactly, a single interval starts and stops. However, if you can flawlessly count a large number of repetitions, just do your best to start and stop the timer in the same place on the first and last repetition. Now you get to multiply your accuracy! Divide the total time, Δt, by the number of intervals, n, this average is an improved measurement of interval! t = Δt / n If you divide the count by the time interval, you get an improved frequency measurement. [1] Frequency is a counted number, n, of full waveform repetitions divided by the total elapsed time, Δt. f = n / Δt


If the clock frequency is 5 MHz how much time is required to execute an instruction of 18 T states?

At a clock frequency of 5 MHz (10 MHz crystal) the 8085 has a clock period of 200 ns. An instruction using 18 cycles would use 3.6 us. (Microseconds)This is for the case with no wait states. Each wait state adds 200 ns. Since an 18 cycle instruction has 5 memory accesses, one wait state per access would add 1 us to the execution time.


If clock frequency is 5 MHz how much time is required to execute an instruction of 18 T states?

At a clock frequency of 5 MHz (10 MHz crystal) the 8085 has a clock period of 200 ns. An instruction using 18 cycles would use 3.6 us. (Microseconds)This is for the case with no wait states. Each wait state adds 200 ns. Since an 18 cycle instruction has 5 memory accesses, one wait state per access would add 1 us to the execution time.


What are the stator of poles?

In an Induction motor synchronous speed is inversely proportion to No. of poles if we increase No. of poles speed will decrease they are derived through formula as under P= 120*f/Ns Where P= No. of Poles f= Rated frequency Ns= Synchronous speed of flux.


What is the distance from Halifax NS and Sackville NS?

There are about 9.778 miles between Halifax, NS and Sackville NS.

Trending Questions
How is compound meter different from a simple meter? In many energy conversions the largest amount of wasted energy often ends up as? What are the three airstream mechanisms that are used to produce sounds? An arrow with a mass of 30g is shot straight up to a height of 130m what is the arrow's initial velocity Please help? What is the energy J of photon with a wavelength of 601nm? What are the benefits of using a greenhouse within a greenhouse for growing plants? How do you remove a scratch PCGS? Can you draw a free body diagram for the car? What are these principles called? How does one calculate much water is found in a 180 pound person? Why is it possible for the objects on a table to remain on the table when the table cloth was pulled away quicly? What is air speed velocity of a sparrow? What happens if you can see your tummy moving and your partner can see it too and it feels like something is moving inside but you have done the blood pregnancy test and it came back negative? What is the formula you use to dertermine acceleration? What happened according to Newton's Law of Inertia and Law of Motion when you slowly pulled the cardboard that had a coin sitting on it with the cardboard covering a glass of water Explain? How does light that is absorbed affect the temperature of the water? Why can't all energy be used to do work? Why is kinetic energy lost in an inelastic collision? How is fusion used in a hydrogen bomb? What is the difference between good and bad conductors?