The weight of 40,000.00 m3 will depend on the material being measured. As a rough estimate, 1 m3 of most common construction materials like concrete or soil weighs around 2 to 2.5 tons. So, 40,000.00 m3 could weigh between 80,000 to 100,000 tons.
The weight of sand varies depending on its density, but on average, one cubic meter of sand weighs about 1.6 to 1.8 tons. Therefore, 100 cubic meters of sand would weigh approximately 160 to 180 tons.
The weight of pea shingle can vary depending on factors such as moisture content and size of the stones. On average, a cubic meter of pea shingle can weigh between 1.4 to 1.6 tons.
The weight of 1 cubic meter (m3) of steel can vary depending on the type of steel. On average, the density of steel is around 7,800 kg/m3. Therefore, 1 cubic meter of steel would weigh around 7,800 kilograms (or 7.8 metric tons).
The weight of 1 cubic meter (m3) depends on the material being measured. For solid materials like concrete, the weight can vary between 1000-2500 kg/m3. For liquids, it can vary between 800-1200 kg/m3. For gases, it can vary depending on the density of the specific gas.
Divide 1 by the stowage factor. if Stowage factor of Salt Petre is 1.02cu meters / ton, 1 / 1.02 = 0.98 So density of Salt Petre (packaged in bulk) is 0.98 metric tonnes per cubic meter.
The weight of sand varies depending on its density, but on average, one cubic meter of sand weighs about 1.6 to 1.8 tons. Therefore, 100 cubic meters of sand would weigh approximately 160 to 180 tons.
The weight of pea shingle can vary depending on factors such as moisture content and size of the stones. On average, a cubic meter of pea shingle can weigh between 1.4 to 1.6 tons.
(Some where) 1 tone sharp sand = .7 M3 (Some where) 1 tone sharp sand dry = 1.60 M3 1 tone sharp Sand, wet - 1.92 M3 1 tone sharp sand loose = 1.44 M3 Iftikhar khan
At the pressure of one atmosphere, 1 tonne of water will occupy between 1.000028 m3 (at 4 deg C) and 1.0434 m3 (at 100 deg C).
The weight of 1 cubic meter (m3) of steel can vary depending on the type of steel. On average, the density of steel is around 7,800 kg/m3. Therefore, 1 cubic meter of steel would weigh around 7,800 kilograms (or 7.8 metric tons).
1000000
Normally somewhere between 1005 and 1015 kg / m3.
Sand is a natural earth material and as such can be somewhat variable depending on the composition of the clasts and the degree of compaction. However see below: Sand (dry) - 1.6 tonnes/m3 Sand (loose / poorly compacted) - 1.44 tonnes/m3 Sand (well compacted) - 1.680 tonnes/m3 Sand (wet) - 1.92 tonnes/m3 Sand (wet, packed) - 2.08 tonnes/m3
By multiplying it by the density of the substance (expressed in tonne/m3) that occupies the volume of 1000m3.
well the density of concrete can vary from 2200kg/m3-2800kg/m3 but 2400kg/m3 is the most common
The tonnage of stone per cubic meter (m³) varies depending on the type of stone. On average, most types of crushed stone weigh between 1.5 to 2.7 tons per cubic meter. For example, granite typically weighs around 2.5 tons per cubic meter, while limestone may weigh closer to 1.6 tons per cubic meter. It's important to check the specific density of the stone type for accurate conversions.
Approximately 141,610 lbs. which is 70.8 tons Answer:Unless you are using Imperial gallons, in which case the weight is 17,000 lb. or 8.5 short tons or 7.7 long tons (about the same value as metric tons or tonnes) These weights are estimate at +4o C where water has its highest density. As the temperature approaches the boiling point the weight for the volume would decrease by about 4%