This question is misguided. You don't need pressure, you need energy.
Energy = work done = mass of water x g (acceleration due to gravity) x height raised.
Pressure = force/area over which it is applied (e.g. the cross section of the water pipe.)
So the pressure needed is given by
P = mgh/area
Be sure your value of g is in the right units for your mass and height measurements.
Differential air pressure will be shown by raising the water level in, for example, a U shaped tube, where differentail pressure is applied between the two arms. Yes, to move the water, energy is used. BTW, energy equals force (weight) times distance, but you are not lifting all the water by one foot.
The relationship between water pressure and elevation is that as elevation increases, water pressure decreases. This is because the weight of the water above exerts less force at higher elevations. The change in water pressure per foot of elevation is approximately 0.433 pounds per square inch (psi) for every foot of elevation gained.
No, the number of gallons of water in one cubic foot does not change when pressurized. The volume of one cubic foot remains the same regardless of the pressure applied. The pressure affects the density of water, not the volume.
Water pressure increases with depth due to the weight of the water above pushing down. This is known as hydrostatic pressure. The deeper you go, the more water there is above, resulting in higher pressure.
At 300 feet of water depth the pressure is about 130 psi
One fathom of water exerts a pressure of approximately 64 pounds per square foot, which is equivalent to 1.42 pounds per square inch.
To raise water 1 foot vertically, you need approximately 0.433 pounds per square inch (psi) of water pressure. This means that for every additional foot of height, the pressure increases by about 0.433 psi. Therefore, to elevate water to various heights, you can multiply the height in feet by this value to find the required pressure in psi.
Water pressure at a depth of about 44 feet is about 20psi
The relationship between water pressure and elevation is that as elevation increases, water pressure decreases. This is because the weight of the water above exerts less force at higher elevations. The change in water pressure per foot of elevation is approximately 0.433 pounds per square inch (psi) for every foot of elevation gained.
Raising the water level on Earth by one foot would require approximately 356,000 cubic kilometers of water.
No, the number of gallons of water in one cubic foot does not change when pressurized. The volume of one cubic foot remains the same regardless of the pressure applied. The pressure affects the density of water, not the volume.
The water pressure increases by approximately 0.43 pounds per square inch (psi) for every foot of water depth. Therefore, at 33 feet deep, the water pressure is about 14.2 psi (33 feet x 0.43 psi/foot). This is in addition to the atmospheric pressure at the surface, which is roughly 14.7 psi, bringing the total pressure to about 28.9 psi at that depth.
Water pressure increases with depth due to the weight of the water above pushing down. This is known as hydrostatic pressure. The deeper you go, the more water there is above, resulting in higher pressure.
The pressure exerted at the base of one cubic foot of water can be calculated using the formula ( P = \rho g h ), where ( \rho ) is the density of water (approximately 62.4 lb/ft³), ( g ) is the acceleration due to gravity (about 32.2 ft/s²), and ( h ) is the height of the water column (1 foot in this case). Thus, the pressure at the base is approximately 62.4 pounds per square foot (psf), as the weight of the water directly translates to pressure exerted over the area. This pressure corresponds to roughly 0.43 psi (pounds per square inch).
Every one feet the pressure raises by 24.9 psi.
Assuming you mean a 14 foot by 20 foot pool, you need the following amount of water to raise it 1 inch:261.818 US liquid gallons; OR218.009 imperial (UK) gallons; OR991.089 liters
0.43197 psi
5300 gallons