answersLogoWhite

0

In a typical aerial burst, only one explosive charge is detonated. This causes the payload carried by the device to disperse and detonate in the air, creating the desired effect.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Related Questions

In a typical aerial burst how many explosions take place What happens in each explosion?

In a typical aerial burst, a single explosion occurs. This explosion disperses the payload carried by the shell into multiple smaller bomblets or submunitions, creating the intended effect over a wider area.


In a typical aerial burst how many explosion take place What happens in each explosion in a firework?

In a typical aerial firework burst, there are usually multiple explosions, often referred to as "breaks." Each explosion occurs when the firework shell reaches its peak altitude and ignites a burst charge, producing a bright flash and scattering the stars (pyrotechnic compositions) into the sky. The first explosion creates the initial visual effect, while subsequent explosions may produce different colors and patterns as the stars ignite sequentially. This sequence creates a stunning display with varying shapes and durations.


What does Aerial mean?

As an adjective, aerial mens "living or taking place in the air".As a noun, an aerial is a rod or wire which receives or transmits radio and television signals.


In which was did the first aerial boming take place?

Guernaca.


When did the cloud burst take place?

war time


The Christmas bombings take place?

the big US aerial bombing that took place on Christmas day.


How to fit an aerial to Fiat punto mk2?

To fit an aerial to a Fiat Punto MK2, start by removing the old aerial by unscrewing it from the base. Clean the area where the new aerial will be mounted, ensuring a good seal to prevent leaks. Then, screw the new aerial into place, making sure it is secure. Finally, connect the aerial wire to the radio and test the reception to ensure proper functionality.


How do you replace an Audi A3 aerial?

To replace the aerial on an Audi A3, start by removing the plastic cover or trim around the base of the aerial, which may require a flathead screwdriver. Next, unscrew the aerial from its base using a wrench or pliers, then disconnect the wiring harness. Install the new aerial by reversing the process: connect the wiring, screw the aerial into place, and replace the trim. Finally, ensure the aerial is securely attached and test the radio reception.


How do you change aerial of Hyundai getz?

To change the aerial on a Hyundai Getz, first, remove the plastic cover around the base of the aerial by gently prying it off. Then, unscrew the aerial by turning it counterclockwise until it comes free. After that, disconnect the cable from the aerial base and replace it with the new aerial by reversing the steps: connect the cable, screw the new aerial in place, and reattach the plastic cover. Always ensure a snug fit to avoid any leaks or damage.


How do you change car aerial vauxhall corsa?

To change the car aerial on a Vauxhall Corsa, first, locate the aerial, typically found on the roof of the vehicle. Carefully unscrew the aerial base using a suitable tool, then detach it from the mounting point. Replace it with the new aerial by securing it in place and ensuring it is tightly fitted. Finally, test the radio to confirm proper functionality.


How do you remove aerial from mg zr 2004?

To remove the aerial from a 2004 MG ZR, start by locating the aerial base on the roof. Use a suitable tool, such as a socket wrench, to unscrew the nut holding the aerial in place. Once removed, gently pull the aerial out of its housing, taking care not to damage any wiring. Finally, if necessary, disconnect any attached cables before fully removing the aerial.


How do i replace the aerial on a Citroen xara Picasso?

To replace the aerial on a Citroën Xsara Picasso, first, locate the aerial base, which is usually on the roof or rear of the vehicle. Carefully unscrew or unclip the existing aerial from its base, taking care not to damage any surrounding components. Install the new aerial by securing it in place and connecting any necessary wires. Finally, test the radio to ensure the new aerial is functioning correctly.