answersLogoWhite

0

A blower is a machine for moving volumes of a gas with moderate increase of pressure. A fan moves large amounts of gas with low increase in pressure.

User Avatar

Wiki User

9y ago

What else can I help you with?

Continue Learning about Physics

What is the purpose of the blower in a fan?

The blower in a fan is responsible for generating airflow by pulling or pushing air through the fan. It helps to circulate air in a room, cool equipment, or exhaust stale air. The blower creates the pressure difference needed to move air efficiently.


Difference between fan blower and compressor?

A fan blower is used to create air flow by pushing air in a specific direction, commonly used for ventilation or cooling purposes. A compressor, on the other hand, is used to increase the pressure of a gas or air by reducing its volume, often found in refrigeration systems or air conditioning units to compress coolant gases. In summary, a fan blower moves air, while a compressor pressurizes air.


Why do you use capacitors on fan motors or blowers?

We use capacitor on fan motor or blower to create phase difference between two winding(Starting & running). This phase difference introduce starting torque on fan motor. Otherwise without capacitor the torque produced in positive Half cycle of AC supply is nullify by the torque produced in negative half cycle.


Why does the blower fan only work on high speed?

The blower motor resistor module is ruined and need replacement. It can be found from below and behind the glove box. Tt may be hard to see, follow the wires to connection that is mounted to the blower unit by two small hex-head screws. I removed the glove box so I could access it easier than trying to go from the bottom in a confined position.


What is the difference between ID and FD fan?

The main difference between an ID (Induced Draft) fan and a FD (Forced Draft) fan lies in their placement in a system. An ID fan is located after the furnace or boiler and helps to draw waste gases out of the system, while an FD fan is positioned before the furnace or boiler to supply fresh air into the system for combustion. ID fans create negative pressure, while FD fans create positive pressure within the system.

Related Questions

What is the difference between fan and blower in air-coolers?

Fan and blower are often used interchangeably and to many people the terms are synonymous.Often it is more of a regional preference,much like engine or motor when referring to an internal combustion engine.


Whats causing my GMC sierra 99 blower to run but nothing comes out?

Do you mean the fan for the heating & AC?


What is the difference between on and auto on a home thermostat?

On will turn the fan or blower on continuously and auto setting will kick off and on according to the temperature setting on the thermostat.


What is the purpose of the blower in a fan?

The blower in a fan is responsible for generating airflow by pulling or pushing air through the fan. It helps to circulate air in a room, cool equipment, or exhaust stale air. The blower creates the pressure difference needed to move air efficiently.


My 2000 quest heater fan only work in the 4 seting whats wrong with it?

it has a bad blower motor resistor Your spelling. or a wire.


How do you check fan relays on 99 Malibu?

To check the fan relays on the 99 Malibu, you can swap the relay between the AC blower and the fan.


How do you replace heater blower fan on a 97 Toyota RAV4?

Remove the wiring harness to the heater blower fan. Remove the retaining bolts. Remove the fan from the blower. Reverse the process to install the new heater blower fan.


2000 jeep wrangler have replaced the climate control panel three times and the connector on the fan speed melts Whats up?

there is an electrical short in the blower motor, making wires overheat. replace blower motor


Why does the blower fan resistor on your 98 Concorde keep burning out?

The blower fan motor is worn out.


Where is the fan located?

engine fan or heater blower fan?


Difference between fan blower and compressor?

A fan blower is used to create air flow by pushing air in a specific direction, commonly used for ventilation or cooling purposes. A compressor, on the other hand, is used to increase the pressure of a gas or air by reducing its volume, often found in refrigeration systems or air conditioning units to compress coolant gases. In summary, a fan blower moves air, while a compressor pressurizes air.


How do you replace a fan blower resistor on a vauxall Corsa?

How do you replace a fan blower resistor on a vauxal Corsa?