0
What else can I help you with?
What is conical flux?
Conical flux is a term used in physics to describe the flow of a field through a conical surface. This arises in various fields such as electromagnetics, fluid dynamics, and heat transfer. The conical shape of the surface plays a role in determining the behavior of the flux.
What is the formula to calculate weight of solid shaft?
The formula to calculate the weight of a solid shaft is weight = volume × density × acceleration due to gravity. The volume of a solid shaft is calculated as π/4 × (diameter)^2 × length, where the density of the material and acceleration due to gravity are constants.
Why the shape of pycnometer cap is conical?
The conical shape of the pycnometer cap helps reduce turbulence during filling, allowing for more accurate volume measurements. It also helps prevent air bubbles from getting trapped, ensuring proper density readings. Additionally, the conical shape minimizes moisture buildup on the cap, which could affect the density measurements.
Is a cube a solid Or is a square a solid?
both are solid.Cube is 3D while square is 2D.cube is used to describe solid shape in 3Dwhile square is used to describe the shape of the surface which is only 2D
Can you show me a picture of a solid?
A rock is an example of a solid. Look at the link for a picture of a rock.
What kind of solid figure is a smokestack?
A conical frustum, tat is, a cone with its apex cut off. It is usually NOT a cylinder because it gets narrower as you get higher.
Frustum of a rectangle?
Since a frustum is a portion of a solid, three-dimensional figure, and a rectangle is a plane, two-dimensional figure, there can be no such thing as the frustum of a rectangle.
What do you call a cone with the top cut off?
This shape is known as a Conical Frustum. Please see the related link.
Why are toothpaste caps conical frustum in shape?
For enabling toothpaste to withdraw, when one stops squeezing the toothpaste tube.
Which solid has 2 circular faces?
-- The frustum of a cone has. -- A right cylinder has.
Why shape of toothpaste cap is conical frustrum?
The shape of a toothpaste cap is typically a conical frustum to facilitate easy squeezing and dispensing of the toothpaste. This design allows for a narrow opening that controls the flow of the paste, preventing excessive amounts from coming out at once. Additionally, the conical shape helps to create a seal when the cap is closed, keeping the toothpaste fresh and preventing contamination. Overall, the frustum shape balances functionality, ease of use, and effective sealing.
What has the author Eric Harold Mansfield written?
Eric Harold Mansfield has written: 'On the flexure of a conical frustum' -- subject(s): Cylinders, Flexure, Shells (Engineering)
Which solid figure has 2 flat surfaces and 0 vertices?
A frustum of a cone.Correct answer is: CYLINDER* * * * *A cylinder is like a special case. If the curved side of a frustum is perpendicular to the flat face, it makes a cylinder but why assume it is perpendicular? The figure could well be a frustum.
How do you find surface area of a frustum?
i have an answer for both a frustum of a pyramid and a frustum of a cone which do you need frustum of a cone just give both of them
What three dimensional shape is a bowl with a lid?
Most likely, a frustum of a sphere.Most likely, a frustum of a sphere.Most likely, a frustum of a sphere.Most likely, a frustum of a sphere.
What is frustum of cone?
There is no frustum of a cone. There is a frustum, which is a cone with the top cut off parallel to the ground.
Im making a conical frustum. i need to know how to get the dimensions so i can cut out a shape to wrap around the frame i have built. any ideas?
Start with a circle of radius equal to the height of a right cone that would be the extension of your frustum. Measure or calculate from the bottom of the frustum up the side and subtract that from the first radius. This remainder is a radius to form a smaller circle concentric with the first one. Now determine the length around the top and bottom of the frustum. This will correspond to a number of degrees within your circles. Draw this angle from the center to the edge of the outer circle. Now cut out the small circle and then the angle section. This should roll into the shape you want. If you use paper for this, be mindful of the grain of the paper. Poster board only rolls in one direction.
