answersLogoWhite

0

The Venturi tube problem refers to the challenge of accurately measuring fluid flow in a Venturi tube due to pressure losses and inaccuracies. This can be solved effectively by calibrating the tube, ensuring proper installation, and using advanced flow measurement techniques such as ultrasonic or electromagnetic flow meters.

User Avatar

AnswerBot

3mo ago

What else can I help you with?

Continue Learning about Physics

What is the operating principle of the venturi meter of flow measurement?

Air flowing quickly over the open top of a vertical tube lowers the air pressure in it. This causes liquid in the tube to rise. (It rises due to the higher pressure acting on the other end. The tube is marked to indicate the wind speed. Alternatively, if the open vertical tube is in still air and it is connected at its lower end with a horizontal tube containing a flowing liquid, the liquid in the vertical tube will fall when the horizontal flow past the lower end increases.


How can siphoning water upwards be achieved effectively?

To effectively siphon water upwards, you can start by filling the siphon tube completely with water, then place one end of the tube in the water source and the other end in a container higher than the water source. Create a vacuum by sucking on the tube or using a pump to start the flow of water upwards through the tube. This method relies on gravity to pull the water up the tube.


Is flow in a Venturi tube laminar or turbulent?

Flow in a Venturi tube can be either laminar or turbulent, depending on the flow rate and Reynolds number. At low flow rates, the flow tends to be laminar, while at high flow rates, it can transition to turbulent flow.


What is the two methods of producing dynamic pressure?

Two methods of producing dynamic pressure are through the use of a venturi tube, which accelerates fluid flow and increases its velocity, resulting in higher dynamic pressure; and through the use of a pitot tube, which measures the impact pressure of a moving fluid and can be used to calculate dynamic pressure.


What is it called when a Bunsen burner air hole is open?

When a Bunsen burner air hole is open, it is called a "venturi effect." This allows air to mix with the gas in the burner tube, creating a hotter and more efficient flame for heating or combustion.

Related Questions

What is Working principle of venturi tube?

Venturi tube is used to for flow measurement. It work on the principle of Bernoulli Equation.


How do you calculated throat diameter for venturi tube?

Using Bernouli's Equation.


Were is the two main sections of a carburetor?

The float bowl and the venturi tube


Your pacific hydrostar pressure washer is blowing oil out of the filler tube for the pump what could cause this problem?

The filler tube has a hole in the side causing the oil to blow out. Remove the filler tube and replace with a threaded plug and the problem will be solved.


Do all shallow well jet pumps use a venturi tube?

All shallow well jet pumps use an ejector (or jet), which consists of a nozzle and venturi tube. Centrifugal pumps on the other hand are also shallow well pumps without a jet.


Why is oil pooling in the spark plug chamber?

REplace the valve cover and tube seals problem solved make sure to repkace the plugs and wires also


What can the term Venturi refer to?

There are many things the term 'Venturi' may reference. One possible use of the word would be a term used to describe a short piece of tube used to measure flow rate.


What is venturitube?

a short tube inserted into a pipeline and used to measure the quantity of a liquid that is flowing in the pipeline well this is a venturi tube. this is probably the same as venturitube. hope that's ok....


Why does 2003 king quad 300 stop after 10 miles?

Check for gas tank vent tube being blocked? On my 2002 it was being placed to deep in front cowling and the end of tube was being covered. Cutting the end of the vent tube at an angle solved the problem.


What is the difference between convergent divergent nozzle and venturi tube?

In case of venturi meter, at the diverging section mach number is less than 1. however in diverging section of a nozzle mach number is greater than 1.


What is the operating principle of the venturi meter of flow measurement?

Air flowing quickly over the open top of a vertical tube lowers the air pressure in it. This causes liquid in the tube to rise. (It rises due to the higher pressure acting on the other end. The tube is marked to indicate the wind speed. Alternatively, if the open vertical tube is in still air and it is connected at its lower end with a horizontal tube containing a flowing liquid, the liquid in the vertical tube will fall when the horizontal flow past the lower end increases.


What is the difference between high velocity and medium velocity water spray system in fire fighting?

The sprinkler head design. High velocity heads have longer nozzles with a venturi tube (a type of curved nozzle) which increases the velocity of the water spray. Medium velocity heads are shorter and do not use a venturi.