0
What else can I help you with?
Is emf a scalar or vector quantity?
Emf has direction within a current loop, though it is not scalar. It's a bit between though as direction should be otherwise accounted for when discussing induced Emf. Not quite either.
What is the key difference between a parallel circuit and a series circuit?
A series circuit pretty much runs in one direction, with each item which uses a load on that circuit one after another in a series. Should one load go out (a lamp, for example) then the entire series is defunct. A parallel circuit has more than one way to run, has a parallel or tandem circuit, so that if one load (our lamp, again) should fail, the electricity has another path (or more) to get to other loads on the circuit.
What effect if any does connecting an ammeter in series with a resistor in a circuit have on the current though the resistor?
Connecting an ammeter in series with a resistor in a circuit will not affect the current through the resistor. The ammeter measures the current passing through it, so it becomes part of the circuit and simply measures the current flowing through the resistor without changing it.
What will induce an electric current in a wire?
There are two ways of doing this; 1) moving a magnet perpendicular(at right angles) to a coil of wire 2) placing a coil of wire in close proximity to another coil carrying an AC current.
Should you connect both ends of a battery in a circuit?
Yes, both ends of a battery should be connected in a circuit to create a continuous flow of electric current. When one end of the battery is connected to one terminal of a component and the other end to the other terminal, a closed circuit is formed, allowing electricity to flow and power the device.
What is induction of electric current?
According to Farady's law, whenever the flux linking with the coil changes, emf will induce in that coil.Actually the material should oppose the flux changes, that opposition is the induced current. Induced current will set own flux, opposite to that of the flux changes.For further details, refer lenz law.
What rule should you use in order to determine the direction of induced EMF in a coil?
The direction of an induced voltage is such that it always acts to oppose any change of current which causes it.So, for example, during the first quarter-cycle of a sine wave, when the current is increasing, the induced voltage acts oppose that change (increase) -in other words, it acts in the opposite direction to that current. During the second quarter-cycle of a sine wave, when the current is decreasing, the induced voltage again acts opposethat decrease that change (decrease) -in other words, it acts in the same direction to that current -trying to sustain that current.
Does an ammeter have a positive and negative terminal?
Yes, an ammeter typically has positive and negative terminals, which are used to indicate the direction of current flow. When connecting an ammeter in a circuit, the positive terminal should be connected to the more positive point in the circuit, while the negative terminal should be connected to the more negative point. This ensures accurate readings of the current flowing through the circuit. However, some ammeters can measure current in either direction without damage, depending on their design.
Why should current be reversed in an AC circuit?
The current in any AC circuit reverses every cycle.
What is emf induced in a motor's coil that tends to reduce the current in the coil of the motor?
BACK emf induced in a motor's coil that tends to reduce the current in the coil of the motor. The answer should be 'back'.
Should current be measured with the power off the circuit?
It will not be possible to measure current unless the circuit is powered and operating.
Is emf a scalar or vector quantity?
Emf has direction within a current loop, though it is not scalar. It's a bit between though as direction should be otherwise accounted for when discussing induced Emf. Not quite either.
What information should be included on circuit breaker labels?
Circuit breaker labels should include the voltage rating, current rating, type of circuit, and the location of the circuit breaker.
What is the key difference between a parallel circuit and a series circuit?
A series circuit pretty much runs in one direction, with each item which uses a load on that circuit one after another in a series. Should one load go out (a lamp, for example) then the entire series is defunct. A parallel circuit has more than one way to run, has a parallel or tandem circuit, so that if one load (our lamp, again) should fail, the electricity has another path (or more) to get to other loads on the circuit.
When using kirchhoffs current law if negative answer is found for current flow what does this indicate?
A negative answer in a Kirchhoff's Current Law calculation indicates that the assumed direction of current flow was incorrect. It suggests that the actual direction of current flow is opposite to the assumed direction. Therefore, the sign of the calculated current should be corrected to reflect the actual flow direction.
What is the maximum current rating for the circuit breaker if the load requires a continuous current of 25 amps?
The maximum current rating for the circuit breaker should be at least 30 amps to accommodate the continuous current of 25 amps required by the load.
What else can be used in the place of a cell in a circuit?
Basically, one option - for providing energy to a circuit - is a cell or battery; the other option is to connect the circuit to an electrical outlet. With a cell, the current will be DC; with an electrical outlet, it will be AC (alternating current, that is, the direction of the current changes several times per second). You should also keep in mind the voltage - household current has a fairly high voltage (110 or 220 volts), compared to a cell (typically around 1.5 volts) or even a car battery (usually 12 volts).
