A laser emits a beam of energy in the form of light. But to get energy out of a laser, we have to put some in. Depending on the type of laser, there are different ways to do this. What is important here is that the energy put into the lasing medium, the energy that is pumped into that medium to stimulate it, to excite it (the actual term), to induce it to lase, is supplied by an outside source, by a pump appropriate to that type of laser. So the pump, that thing outside the medium that stimulates it to induce it into lasing, is pumping when it is exciting the medium. Hope this was, um, coherent....
Absolutely. There are many lasers used in industry for metal cutting. CO2 lasers are the most common, but there are many other types.
Cold lasers are safer and deal less pain than hot lasers. Cold lasers are usually used for repairing skin damage and treating pain and inflammation. Hot lasers are simply used for burning things.
no not all lasers are really
Lasers of different wavelengths can be purchased from many sites online, such as Lexel Laser, and Wicked Lasers. Be sure to check the legality of the lasers in your country or risk losing them at customs.
All tunable LASERs are LASERS, however not all LASERS are tunable. In a tunable laser the lasing medium, which is typically a gas, dye or crystal, can be altered to produce slightly different frequencies, thus allowing the laser to be 'tuned' or frequency changed where most LASERS produce a very narrow band of radiation frequencies.
Ans. Optical pumping methods are very ineffective for gas lasers because gas atomsshow sharp energy, levels as compared to solids, which are characterized by energy bands raTher than energy levels. Thus for gas laser the electrical discharge is used for pumping.
Ali Javan has written: 'Photoexcitation of lasers and chemical reactors for NASA missions' -- subject(s): Environmental aspects, Environmental aspects of Lasers, Lasers, Optical pumping, Remote sensing
gas lasers do not usually lend themselves to lamp pumping because the absorption lines are typically much narrower than the usual broadband emission of the lamp. Electrical pumping of gas lasers ,on the other hand can be a fairly efficient process because the linewidth of excitation cross section of a given transition by electron impact is usually quite large
Absolutely. There are many lasers used in industry for metal cutting. CO2 lasers are the most common, but there are many other types.
Here they are:Red: 650nmGreen: 532nmBlue: 473nmViolet: approx 400nmYellow: approx 575nmHere is a list of some of the different types of lasers and what they are used for.Carbon Dioxide Laser (Gas) - Material processing, surgeryNitrogen Laser (Gas)- Pumping of dye lasers, measuring air pollution, scientific researchHelium-Neon Laser (Gas) - barcode scanning, alignment, optical demonstrationsHydrogen Fluoride Laser (Chemical) - Used in research for laser weaponry by the U.S. DOD
its not lasers are Diffractions it is refractions
Since the early 1970s Erchonia lasers have been classified by wavelength and maximum output powers into four classes. The lasers are used in treatment of neck and shoulder pain, breast augmentation, acne, laser assisted body augmentation. The types of lasers they use for these treatments include 3LT Lasers, Custom Design Lasers and Zerona Lasers.
R. J. De Young has written: 'Scaling blackbody laser to high powers' -- subject(s): Lasers, Blackbody radiation 'Lasant materials for blackbody pumped-lasers' -- subject(s): Solar-pumped lasers, Lasers in astronautics, Energy conversion, Laser pumping, Blackbody radiation, Laser cavities, Laser propulsion, Black body radiation 'A blackbody-pumped CO-N' -- subject(s): Lasers
Lasers can be used to treat wrinkles by a laser resurfacing procedure. It can be done with two types of lasers: one that removes thin layers of skin and the other type that stimulates collagen growth.
The cardiac muscle of the heart has primary responsibility for pumping blood throughout the body.
No; only some types of crystals, gases, etc. can be used in lasers.
Tunable lasers can be tuned in various manners. Some of these include single line and multi line tuning. Narrow band tuning is also used to tune various lasers as well.