answersLogoWhite

0

a black weiner

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Physics

How do you put a metal rod into a hole in a metal cylinder but its too tight Do you heat the rod and cool the cylinder or cool the rod and heat the cylinder?

You should heat the metal cylinder and cool the metal rod. Heating the cylinder will cause it to expand, making it easier to insert the rod. Cooling the rod will cause it to contract, allowing it to fit into the hole more easily.


What will happen if a metal rod is rubbed together with silk?

When a metal rod is rubbed together with silk, electrons transfer from the metal rod to the silk due to the difference in their electron affinities. This creates a charge imbalance, with the metal rod acquiring a positive charge and the silk a negative charge. This is known as triboelectric charging.


The metal rod becomes negatively charged as well through which process?

The metal rod becomes negatively charged through a process called conduction. When a negatively charged object is brought near the metal rod, electrons on the surface of the rod are repelled, causing them to move to the end of the rod farthest from the negatively charged object. This redistribution of electrons creates a negative charge on the metal rod.


When metal rod is rubbed against polythene bag or sweater it attracts or not?

When a metal rod is rubbed against a polythene bag or sweater, the rod becomes charged with static electricity. The metal rod may be attracted to the polythene bag or sweater due to the opposite charges present on each material.


What is the transfer of heat through a metal rod?

Heat transfer through a metal rod occurs primarily through conduction, where thermal energy is transferred from atom to atom within the material. The rate of heat transfer is influenced by the thermal conductivity of the metal, the temperature difference across the rod, and the cross-sectional area of the rod. Heat conduction in a metal rod follows Fourier's Law of Heat Conduction.

Related Questions

How can I effectively cut threaded rod?

To effectively cut threaded rod, use a hacksaw or a reciprocating saw with a metal-cutting blade. Secure the rod in a vise to prevent it from moving while cutting. Make sure to wear safety goggles and gloves to protect yourself from metal shards. Cut slowly and steadily to avoid damaging the threads.


How can I safely and effectively cut threaded rod?

To safely and effectively cut threaded rod, use a hacksaw or a power tool with a metal-cutting blade. Secure the rod in a vise to prevent it from moving while cutting. Wear safety goggles and gloves to protect yourself from metal shards. Cut slowly and steadily to avoid damaging the threads.


How can I securely attach a lamp to a ceiling using a threaded rod?

To securely attach a lamp to a ceiling using a threaded rod, first, drill a hole in the ceiling that is the same diameter as the threaded rod. Insert the threaded rod through the hole in the ceiling and secure it with a nut and washer on both sides of the ceiling. Then, attach the lamp to the threaded rod using appropriate hardware. Make sure the lamp is securely fastened to the threaded rod to prevent it from falling.


How can I safely and accurately cut threaded rod to the desired length?

To safely and accurately cut threaded rod to the desired length, follow these steps: Measure and mark the desired length on the threaded rod using a tape measure and a marker. Secure the threaded rod in a vise or clamp to prevent it from moving during cutting. Use a hacksaw or a reciprocating saw with a metal-cutting blade to cut the threaded rod along the marked line. Apply steady pressure and make smooth, even strokes while cutting to ensure a clean and accurate cut. After cutting, use a file to remove any burrs or sharp edges from the cut end of the threaded rod. Finally, use a die to clean up the threads on the cut end of the rod to ensure proper fitment with nuts or other fasteners. Remember to wear appropriate safety gear, such as gloves and eye protection, when cutting threaded rod.


What is a c-clamp?

A C-clamp is a tool, essentially it is a C-shaped piece of metal with one flat surface and a threaded rod with a "foot" and handle on opposite ends. Turning the threaded rod in a clockwise direction closes the C and forms a clamp. See the link below for an image.


How can I effectively cut a threaded rod?

To effectively cut a threaded rod, use a hacksaw or a power tool like a reciprocating saw with a metal-cutting blade. Secure the rod in a vise to prevent it from moving, and wear safety goggles and gloves. Measure and mark where you want to cut, then slowly and steadily cut through the rod using the saw. After cutting, use a file to smooth out any rough edges.


What kind of things would require using a threaded rod?

One would find a threaded rod useful to partake in ironmongery. To purchase or find different variations of threaded rods, one could visit Ironmongery Online.


What is the function of the inner tie rod?

on a steering rack the inner tie rod is threaded and will be the mount for the outer tie rod.


What is the yield strength of B7 threaded rod?

105000 psi yield 125000 psi tensile


Where can one purchase an Acme threaded rod?

One can purchase Acme Threaded Rods from UseEnco. You can also purchase them from DependableAcme or from the onlinestore at Metalbythefoot that has a large selection.


What does a tire rod look like?

What you're referring to is a tie-rod. A tie-rod is a hardened straight rod that is threaded on either end. On the ends are ball joints that connect the steering knuckle to the steering rack.


How do you attach PVC to plywood?

Clevis hangers attached to threaded rod with a rod coupling to give the proper amount of pitch