Mil to Gauge ratio
The sizes of wire and sheet metal are not based on thickness or weight, but the number of times that the metal has to be drawn through the process to make it any given thickness. The higher the number the more often it has had to be drawn to make it thinner, so "1 gauge" is the original rod "10 gauge" is the same rod after being drawn 10 times. The sizes of plastics are measured using a micrometer, so the sizes are thicker 1 mil = 1/1000 inch = 25.4 micron = 100 gauge.
4.7 mil paper is thicker than 20 lb paper. Mil is a unit of measurement used to describe the thickness of paper, with 1 mil equal to 0.001 inches. Therefore, 4.7 mil paper would be approximately 4.7 times thicker than 20 lb paper.
A cc (cubic centimeter) is the same as Mil, or milliliter, or Ml. Thus 1/2 of one would be 1/2 of the other.
The bulk modulus of oil can vary based on factors such as temperature and pressure. However, for oil meeting the MIL-L-23699 specification, the typical bulk modulus is around 1.8-2.0 GPa.
Assuming copper conductor at 20 degrees celcius, you can use a chart to determine the resistance of a length of conductor. You must know it's size (AWG, for American wire gauge) and the look up the resistance per 1000 feet from any table. For a specific length of conductor, you just multiply the table's value by the proportion of 1000 feet that's actually the lenght of the conductor: table's resistance value x length in feet/1000 feet. For other temperatures or materials (i.e., aluminum), you must use a different formula: Rc = (K x L)/cmil where Rc = conductor resistance, K = "K factor" (see below), L = length of conductor and cmil is the cross sectional area of the conductor in circular mils (see the same chart referred to above). The K factor for different materials is Copper: 10.8@25OC, 11.8@50OC and 12.9@75OC Aluminum: 17.0@25OC, 19.0@50OC, 21.2@75OC The K factor is the resistance of one circular mil-foot (cmil-foot) of the material. A mil is 0.001" and a circular mil is a circle 1 mil in diameter. A circular mil-foot is a length of the material 1 circular mil in cross-sectional area and 1 foot long. The cmil value of a given wire gauge is the cross-sectional area in circular mils.
The mil measurement of the thickness of the plastic sheet is 1/1000th of an inch.
Gauge is the term that comes to mind, such as 12 gauge (ga.) wire. With plastic bags, one might use mil, such as a 3 mil garbage bag. "Mil" indicates thousandths of an inch.
A thickness of 68 mil is equivalent to 0.068 inches. In terms of gauge, this measurement falls around 16 gauge in the standard gauge conversion for metal thickness, although variations can occur depending on the material being measured. Generally, mil is a term used primarily in the context of plastic sheeting and other materials, where 1 mil equals 1/1000 of an inch.
no
If you are referring to wire thickness according to American Wire Gauge, 12.6 mil or 321 microns.
To accurately measure mil thickness, use a micrometer or a mil gauge tool. Place the tool on the material and apply pressure to get a reading in mils. Make sure to measure at multiple points for accuracy.
See this link: http://www.backyardcitypools.com/vinyl-pool-liners/Mil-Vs-Gauge.htm
'Mil' is an abbreviation for 'millimeter' when referring to the thickness of environmental liners. It is used to measure the gauge or thickness of the liner, with a higher mil indicating a thicker liner that offers more protection against leaks or punctures.
PVC gauge is the thickness of the PVC material: 1 gauge = 1/100 mil = 1/100,000 inch = 25.4/100000 millimetre = 0.254 micrometre
Gauge and mil refer to the thickness of the liner. To find the thickness when listed by gauge ask for the type of material and check for the converted value ( ie a 10 gauge liner may equate to perhaps a 0.14 inch thickness material , 8 gauge may be 0.12 inches etc ) The mil value usually refers to a millimeter thickness (ie 15 mil should be thicker than a 10 mil ) >KEEP IN MIND THAT THE MIL NUMBER IS NOT IN INCHES , so make sure what the mil value is given in millimeters or inches then you can compare the different thicknesses. If the pool dealer doesnt know the difference you may want to find another dealer
160 mil is equivalent to 0.160 inches or approximately 4.06 millimeters. The term "mil" refers to one thousandth of an inch, so 160 mil indicates a substantial thickness often used in applications like plastic sheeting or industrial materials.
poly bags are just plastic bags and their mil size is the thickness of the bag, check out http://www.millersupplyinc.com/ for more info