0
What else can I help you with?
How calculate peak torque?
Peak torque is typically measured by running the engine on a dynamometer and recording the maximum twisting force produced by the engine. The peak torque value is usually given in foot-pounds (lb-ft) or Newton-meters (N-m) and represents the maximum rotational force that the engine can generate at a specific engine speed.
What is the velocity of a ball thrown upward at W ft sec?
The velocity of a ball thrown upward at W ft/sec will gradually decrease due to gravity until it reaches its highest point (at which the velocity will be 0 ft/sec). After reaching the peak, the ball will then start to fall back down, increasing in velocity until it reaches the ground.
How many gallons in 20 x 43 lazy l pool 3 ft shallow end 8 ft deep end?
To calculate the volume of a lazy L pool with dimensions 20 ft x 43 ft and varying depth (3 ft shallow end, 8 ft deep end), you first need to determine the average depth. Using the formula for the volume of a trapezoidal prism (V = 1/2 * (depth1 + depth2) * length * width), the average depth is (3 + 8) / 2 = 5.5 ft. So, the volume of the pool would be 20 ft * 43 ft * 5.5 ft = 4730 cubic feet. To convert cubic feet to gallons, you would multiply by 7.48, resulting in approximately 35,407 gallons.
A car driving on the turnpike accelerates uniformly from 91.0ft per second to 118ft per second in 3.20 seconds. what is the cars acceleration?
The car's acceleration can be calculated using the formula: acceleration = (final velocity - initial velocity) / time. Plugging in the values gives acceleration = (118 ft/s - 91 ft/s) / 3.20 s = 8.44 ft/s^2. So, the car's acceleration is 8.44 ft/s^2.
How many gallons in 8 ft x 8 ft x 3 ft container?
There are approximately 1,006 gallons of water in an 8 ft x 8 ft x 3 ft container.
What does "FT" stand for in regard to FTIR spectroscopy?
"FT" stands for Fourier Transform in FTIR spectroscopy.
Where is IR peak of Silicon Carbide using FT IR spectroscopy?
The IR peak of silicon carbide typically falls within the range of 800-1200 cm^-1, with specific peaks at around 800-850 cm^-1 and 970-1100 cm^-1. These peaks are attributed to the Si-C stretching vibrations and the Si-C-Si bending modes in the silicon carbide structure as observed in FT-IR spectroscopy.
How tall is lassen peak?
Lassen Peak is about 10,457 ft. tall.
Highest peak in rocky mountain national park?
Longs Peak at 14,00 ft
What is the difference between NMR and FT- NMR instrumentation?
NMR (Nuclear Magnetic Resonance) spectroscopy measures the absorption of electromagnetic radiation by nuclei in a magnetic field, providing structural and chemical information about molecules. FT-NMR (Fourier Transform-NMR) is a technique that enhances the speed and sensitivity of NMR by using Fourier transformation to convert the time-domain signal into a frequency-domain spectrum, allowing for higher resolution and improved signal-to-noise ratio. Essentially, FT-NMR is a more advanced and efficient method of performing NMR spectroscopy.
What is the higest peak in Bulgaria?
The highest peak is Musala 2,925 m (9,596 ft).
What is the height of Moldoveanu Peak?
The elevation of Moldoveanu Peak is 2,544 m (8,346 ft).
How tall is the geladandong peak?
The peak rises to a height of 21,722 ft (or 6,621 metres).
How high is Eagle Peak?
3000 ft.
What is the highest peak in India?
Kanchenjunga at 8586 mt. (28,169 ft.) is the highest peak in India.
How tall is Tom Hank?
Tom Hanks is 5 ft 11.5 in or 181 cm peak height was 6 ft 0 in or 183 cm.
How tall is Granite Peak Montana?
12,799 ft
