A resistance box is a device that contains a set of fixed resistors that can be connected in various combinations to achieve different resistance values. A rheostat is a variable resistor that can be adjusted to change the resistance in a circuit. A resistor is a general term for a component that resists the flow of electrical current in a circuit and comes in fixed resistance values.
These devices could, in theory, be interchangeable. Variac is a (typically single coiled) variable transformer, whereas rheostat is a variable resistor. Although they may look just the same, they differ in one aspect - wire resistance. It should be as low as possible for variac, but it can differ on rheostats. So-you can use wire rheostat as a low efficiency variac and you can use wire variac as ridiculously huge rheostat, resistive range of which serves no practical purpose.
A rheostat and a potentiometer are two different applications for the same device, a variable resistor. These devices have three terminals. Two terminals are connected across the complete resistor, while the third terminal is connected to a controllable wiper. The variable resistance is provided between the wiper terminal and either one of the other two terminals.When used to control current, it is called a rheostat. When used to control voltage, it is called a potentiometer.
A carbon pile rheostat is used to control the amount of electrical current flowing through a circuit by varying the resistance. It works by adjusting the amount of contact between carbon discs, which changes the resistance and therefore the current flow.
The phase difference between the current through the resistor and inductor in an AC circuit is 90 degrees.
Resistance is the property of a conductor, which determines the quantity of current that passes through it when a potential difference is applied across it. A resistor is a electrical componet with a predetermined electrical resistance, like 1 ohm, 10 ohms 100 ohms 10000 ohms etc.. depending on how much current you want to pass through a circuit, you would design the circuit with the required resistors
The difference between a variable resistor and a rheostat is the same as the difference between six and half a dozen.
A non-ohmic resistor doesn't have a constant resistance. A ohmic resistor has a constant resistance.
Depending on the situation. The purpose of the rheostat is use to change the resistance of the circuit. The rheostat is use to define Ohm Laws the 2nd situation is use to find out what the fixed resistor's resistance. 3rd purpose : used to control the resistance of circuit. eg Radio
These devices could, in theory, be interchangeable. Variac is a (typically single coiled) variable transformer, whereas rheostat is a variable resistor. Although they may look just the same, they differ in one aspect - wire resistance. It should be as low as possible for variac, but it can differ on rheostats. So-you can use wire rheostat as a low efficiency variac and you can use wire variac as ridiculously huge rheostat, resistive range of which serves no practical purpose.
Resistor is a current a insulator is a not conductive and conductors can conduct.
Slide wire rheostat: We can get continuous variation in resistance. It is used in such situations where we are supposed to get a fixed current flowing throug the circuit-some integral value like 1,2 etc instead of 1.343 and all. Resistance box: It is a deveice used to get a specific value of resistance. We may not get a simple value for current.
Resistance box will provide resistance of discrete values such as 1, 2, 3 ohms or 0.1,0.2, 0.3 ohms. So interim values are not possible. But rheostat gives a chance to vary the resistance continuously. It may be 5 ohm or even 5.769 ohm. So just to fix current for a specified value such 1.5 ampere resistance box will not be suitable where as a rheostat is the most suitable.
Variable resistors means that a resistor which can change its resistance by control by any person or it self and fixed resistor means that it can not change its value.
I am not sure how the two objects of equal resistance are supposed to be connected. But for a current to flow, for example across a resistor, there must be a voltage difference between the terminals of this resistor.
A rheostat and a potentiometer are two different applications for the same device, a variable resistor. These devices have three terminals. Two terminals are connected across the complete resistor, while the third terminal is connected to a controllable wiper. The variable resistance is provided between the wiper terminal and either one of the other two terminals.When used to control current, it is called a rheostat. When used to control voltage, it is called a potentiometer.
It is a variable resistor. Basically, the same as when you turn up or down the heat on an electrical oven or radio.
Resistors are either fixed value, or variable. A variable resistor has three terminals; one at either end and one attached to a moving 'wiper', and can be connected either as a potentiometer or as a rheostat. So 'potentiometers' and a 'rheostats' are different applications for variable resistors. A potentiometer uses all three terminals, and is used to control levels of potential; whereas a rheostat uses just two of the three terminals, and is used to control current.