0
What is the frequency at which a system oscillates when it is disturbed called?
Wiki User
∙ 9y ago
Natural Frequency
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What is the measure of how many times an object vibrates per second?
The word for "number of vibrations per second" or "cycles per second" is frequency. Otherwise, you might be looking for the density and bulk modulus of the medium, and the intensity of the energy... which will establish the natural frequency of a system.
What is the number of vibrations that occur in one second?
That depends on what kind of a system the local oscillator is part of. In a simple AM receiver, it's typically 455 KHz above the frequency of the incoming signal of interest. In a consumer FM radio, that figure is 10.7 MHz above. In a 'legacy' analog microwave receiver, it's almost always spaced 70 MHz from the received carrier, and since the ubiquitous advent of split-mount digital microwave equipment, with the RF system clamped to the antenna, there's no telling any more ... you always have to look in the book (if that information is even included in the book).
What are the highest-frequency and and the lowest-frequency parts of the EM system?
Lowest-frequency: Radio Waves Highest-frequency: Gamma Waves Hope this helped! :)
What does overtone mean?
An overtone is a natural resonance or vibration frequency of a system. (see link for "Calculations of Harmonics from Fundamental Frequency")
Why does the resonant frequency have to be equal to the natural frequency of the system so the resonant can happen?
Let's say that that's what resonance is all about. Anyway, it need not be exactly the same frequency; just close enough.
What is the relationship of the frequency with the fundamental in the square wave frequency response?
The natural frequency of the spring refers to its frequency when hit or struck. Its lowest frequency is called fundamental frequency. For a spring, the 1st mode of natural frequency is fundamental frequency.
What is the difference between resonance and resonant frequency?
resonance is the behavior of resonant frequency while resonant frequency is the cause of it. There are basically two types of resonance; Electrical and Magnetic. Resonant frequency is that particular frequency for a system for which the system performs its best. while the system at that particular situation can be called the system at resonance
What is the system bus and frequency called?
Front Bus and 1600
What is called a high-frequency waves used in a sound navigation and ranging system?
lwteyg
What do you mean by resonance?
Resonant means something vibrates at a given frequency. Usually if you can get an object to resonate at its resonant frequency - it will disintegrate ! For example - if you tap a wine-glass, it 'rings' - that's it's resonant frequency. Now - take a speaker and play the exact frequency through it, while holding it close to the glass - after a few seconds it will shatter because the glass vibrates too fast.
What is the frequency deviation for frequency modulation?
Deviation ratio: In a frequency modulation system, the ratio of the maximum frequency deviation of the carrier to the maximum modulating frequency of the system under specified conditions
If frequency increased is that more hazardous or less hazardous?
The answer depends on frequency of what! It the frequency of safety checks is increased then it makes a system less hazardous. If the frequency of changes to he system is increased, the system becomes more hazardous.
What is the measure of how many times an object vibrates per second?
The word for "number of vibrations per second" or "cycles per second" is frequency. Otherwise, you might be looking for the density and bulk modulus of the medium, and the intensity of the energy... which will establish the natural frequency of a system.
What occurs if the frequency of a force applied to system matches the natural frequency ofvibration of the system?
Resonant
If you multiply the system bus frequency by the multiplier you get the?
processor frequency
If you multiply the system bus frequency by the multiplier you get what?
processor frequency
Why must the oncoming generator on a power system be parralleled at a higher frequency than that of the running system?
If the frequency of the oncoming generator is slightly higher than the system frequency, the phase angle between the system and generator voltages will slowly change at a frequency equal to the difference between system and generator frequencies.
