0
The standard operating pressure for R-22 refrigerant in air conditioning systems is typically between 68 to 70 psi on the low side and 250 to 270 psi on the high side when the system is running. These values may vary depending on factors such as ambient temperature and specific system requirements.
What else can I help you with?
What is the condensing temp for a head psi of 296 psig for an r22 system?
The condensing temperature for an R22 system with a head pressure of 296 psig would typically be around 120-130°F. This is based on the saturation temperature corresponding to a pressure of 296 psig on the R22 pressure-temperature chart.
What are the pressure on r22?
The pressure for R22 refrigerant varies depending on the temperature and phase of the refrigerant. For example, at 40°F, the pressure can be around 60 psi on the low side and 185 psi on the high side. It's important to consult a pressure-temperature chart for specific values.
What should be the suction pressure for R22?
The recommended suction pressure for R22 varies depending on the specific operating conditions and equipment. However, typical suction pressures for R22 range from 60-70 psi for air conditioning applications. It's important to consult the manufacturer's guidelines or an HVAC professional for specific recommendations.
What should be our suction pressure on a r22 unit on an 83 degree day?
The suction pressure of an R22 unit on an 83-degree day will vary depending on factors such as indoor temperature, coil condition, and humidity levels. A typical range for suction pressure on an R22 unit could be around 60-70 psi on an 83-degree day. It's important to refer to manufacturer specifications and consider other system parameters for an accurate assessment.
What is the cost for 125 pounds of r22 commercial grade refrigerant?
The cost of 125 pounds of R22 refrigerant can vary depending on market prices and supplier rates. On average, you can expect to pay anywhere from $50 to $100 per pound for R22 refrigerant. Therefore, the total cost for 125 pounds of R22 could range from $6,250 to $12,500.
What is the condensing temp for a head psi of 296 psig for an r22 system?
The condensing temperature for an R22 system with a head pressure of 296 psig would typically be around 120-130°F. This is based on the saturation temperature corresponding to a pressure of 296 psig on the R22 pressure-temperature chart.
Can R22 be used in a R12 system?
No, R22 is for refrigerators and home AC. It runs at a different pressure and you can't use one for the other.
R22 low side pressure?
Low predsure very high
What are the pressure on r22?
The pressure for R22 refrigerant varies depending on the temperature and phase of the refrigerant. For example, at 40°F, the pressure can be around 60 psi on the low side and 185 psi on the high side. It's important to consult a pressure-temperature chart for specific values.
What is a low pressure refrigerant under EPA's refrigerant recycling regulations?
R22
What should be the suction pressure for R22?
The recommended suction pressure for R22 varies depending on the specific operating conditions and equipment. However, typical suction pressures for R22 range from 60-70 psi for air conditioning applications. It's important to consult the manufacturer's guidelines or an HVAC professional for specific recommendations.
What should the suction pressure be on a 85 degree day on a R22 split unit?
60psi
What refrigerant is a low pressure refrigerant under EPA's refrigerant recycling regulations?
R22
What refrigerant is considered a low-pressure refrigerant under EPA's refrigerant recycling regulations?
R22
Can you use a 134a freon manifold gauge set for R22?
No. the pressure are different, r22 runs at a fairly low pressure and you shouldn't be worried about blowing your gauges, but you won't be able to determine your super-heat or sub-cooling. for a about $100cdn you can buy the right gauges.
What should be our suction pressure on a r22 unit on an 83 degree day?
The suction pressure of an R22 unit on an 83-degree day will vary depending on factors such as indoor temperature, coil condition, and humidity levels. A typical range for suction pressure on an R22 unit could be around 60-70 psi on an 83-degree day. It's important to refer to manufacturer specifications and consider other system parameters for an accurate assessment.
What is the correct pressure on the high side and low side on R22 at 95 degrees?
150 high 75 low
