0
What else can I help you with?
Why should meter rule be balanced on the wedge edgewise?
Balancing the meter rule on the wedge edge-wise ensures that the weight of the meter rule is evenly distributed on both sides, leading to a stable and accurate reading. Placing it edgewise helps minimize the effect of friction and other external forces that may affect the balance of the rule.
What are the precautions when using a meter rule?
1 place the scale in contact with the object along its length starting from 0. if the zero mark is not clear use any other full mark of the scale. 2 your eye must be exactly in front of the point where the measurement is to be taken.
Is metrre rule balanced edgewise on the wedge in stable equilibirium?
Yes, a meter rule balanced edgewise on a wedge can achieve stable equilibrium. If the center of mass of the meter rule is directly above the point of contact with the wedge, the system will be in stable equilibrium. Additionally, the gravitational force and normal force acting on the system need to be balanced to maintain equilibrium.
How can you avoid parallax errors when measuring a length with a meter rule?
To avoid parallax errors when measuring a length with a meter rule, ensure your eye is directly in line with the measurement marking on the ruler. This reduces the apparent shift in position when viewing the measurement scale. Place the ruler flat on the surface being measured and read the measurement at eye level for accuracy.
What is the weight per square meter of 2mm thick HRCA mild steel sheet?
The weight of mild steel can vary slightly depending on the exact composition, but as a general rule of thumb, the weight of a 2mm thick hot rolled commercial quality mild steel sheet is approximately 15.7 kilograms per square meter.
What is the zero error and the reading uncertainty for meter rule?
Ah, the zero error is when the meter rule doesn't start exactly at zero, so you have to adjust your readings accordingly. The reading uncertainty is the smallest division on the meter rule, showing how precise your measurements can be. Remember, it's all part of the beauty of capturing nature's details with your measurements.
What is the uncertainty of a meter rule?
The uncertainty of a meter rule typically depends on its smallest division, which is usually 1 millimeter (0.001 meters). Therefore, the absolute uncertainty is often considered to be half of the smallest division, resulting in an uncertainty of ±0.5 mm (±0.0005 meters). This means that any measurement taken with a meter rule can be expected to have a possible error of ±0.5 mm.
What is the smallest reading on the meter rule?
0.5
What type of meter shows reading on a non-linear scale?
-- analog ohm-meter -- analog power meter -- analog audio level meter -- slide-rule multiplication/division scales -- slide-rule tangent/cotangent scales -- analog tuning dial on an AM radio
Why should meter rule be balanced on the wedge edgewise?
Balancing the meter rule on the wedge edge-wise ensures that the weight of the meter rule is evenly distributed on both sides, leading to a stable and accurate reading. Placing it edgewise helps minimize the effect of friction and other external forces that may affect the balance of the rule.
What is the function of a meter rule?
Measurement of length.
IN Trapezoidal Rule for Numerical Integration How you can find error?
in trpezoidal rule for numerical integration how you can find error
When uncertainty in position of an electron is zero what will be uncertainty in momentum?
Werner Heisenberg's (1901-1976) uncertainty principle: ∆x∙ ∆(mv) ≥ h / 4π x = uncertainty; m = mass; v = velocity To solve for ∆x... ∆x = h / 4πm∆v
What is the smallest division on the meter rule is?
The smallest division on a meter rule, also known as a meter stick, is typically 1 millimeter (mm). This means that each small line or marking on the meter rule represents a distance of 1 mm. The meter rule is divided into centimeters (cm) and millimeters (mm), with each centimeter divided into 10 millimeters. The smallest division of 1 mm allows for precise measurements to be taken using the meter rule.
What is the difference between a meter rule and a meter ruler?
If the calibration starts from the edge of the stick then it is a meter rule Basically "0" starting from the edge And if it is a meter ruler ,there is like half inch of empty space before 0
What is the accuracy of a meter rule?
0.5mm
What is error in measuring young's modulus of wooden meter rule?
The error in measuring Young's modulus of a wooden meter rule can arise from several factors, including inaccuracies in measuring the dimensions of the rule, imprecise measurements of the applied force, and variations in the material properties of wood, which can differ due to knots and moisture content. Additionally, the method of applying force and any potential slippage during the measurement can also contribute to errors. Since wood is an anisotropic material, its response to stress may not be uniform, further complicating accurate calculations of Young's modulus.
