The question seems absurd has no meaning.
measuring cylinder is a device to measure the volume.
if you want to find density of a cube, you an find volume displaced and knowing mass can find the density - Archimedean principle
it is beyond the scope of this page to answer fully
Density of an object is defined as mass per unit volume. Density - mass/volume (m/v) To find the density of a liquid using a graduated cylinder, you first of all take a measurement of the mass of the empty graduated cylinder (m1) and write it down. Lets say the mass is 0.5 kg (500 grams) Then fill the cylinder with the liquid that you want to find the density for and note down the volume (v). For easier calculation take 1 liter of the liquid. Now take a measurement of the mass of the cylinder with the liquid (m2) in it and write it down. Subtract the mass of the empty cylinder from the mass of the cylinder and liquid combined to get the mass of the liquid (m = m2 - m1). Now divide the result z by the volume (v) of the liquid. density = m/v
Two common pieces of equipment used to find density are a balance and a graduated cylinder. The balance is used to measure the mass of the object, while the graduated cylinder is used to measure the volume of the object. By dividing the mass by the volume, you can determine the density of the object.
This depends upon the phase of the material whose density you wish to find. Fir an irregularly shaped solid, you would have to find the volume using a graduated cylinder (to measure how much liquid it displaces) and then weigh it on a scale (probably a triple beam balance). A regularly shaped solid would not require a graduated cylinder, you could just get its measurements with a ruler. A liquid could be measured using a graduated cylinder and a scale. A gas could have its density relative to that of the air measured by observing its buoyancy vs. weight measured in a balloon. That is a bit more complicated.
You can use a graduated cylinder to measure an object's volume.Fill the cylinder with water up to some convenient mark that's deeper than the object, and notethe volume of water in the cylinder. Than immerse the object in the water in the cylinder and notethe volume again. The difference between the two volume readings is the volume of the object.In my house, we have graduated cylinders which we refer to as our "measuring cups".
The least dense liquid is found at the bottom of the graduated cylinder, because the less dense it is, the farther it will go down in th graduated cylinder.
Mass and volume are needed to calculate the density of a graduated cylinder.
You cannot measure the mass of a solid with a graduated cylinder.
not quite. you can measure volume in a graduated cylinder. you can use a scale, water, and a graduated cylinder to find out the density of an object by filling the graduated cylinder to an easily calculated point (250) then dropping your object in the water making sure none splashes out then measure the difference, then weigh it and divide the mass by volume to get density.
density -------- Graduated cyllinders are used to measure volumes of liquids, powders or fine granules.
densities. Liquids will arrange in order of decreasing density from bottom to top in the graduated cylinder. Liquids with higher density will sink to the bottom while those with lower density will float on top.
Density of an object is defined as mass per unit volume. Density - mass/volume (m/v) To find the density of a liquid using a graduated cylinder, you first of all take a measurement of the mass of the empty graduated cylinder (m1) and write it down. Lets say the mass is 0.5 kg (500 grams) Then fill the cylinder with the liquid that you want to find the density for and note down the volume (v). For easier calculation take 1 liter of the liquid. Now take a measurement of the mass of the cylinder with the liquid (m2) in it and write it down. Subtract the mass of the empty cylinder from the mass of the cylinder and liquid combined to get the mass of the liquid (m = m2 - m1). Now divide the result z by the volume (v) of the liquid. density = m/v
If you are going to weigh a liquid in a graduated cylinder, the weight that you will get when you place the cylinder on the scale will be the combined weight of the cylinder and its contents. To find the weight of the contents alone, you therefore have to subtract the weight of the empty cylinder. And to calculate density you need to know both the weight and the volume.
If you are going to weigh a liquid in a graduated cylinder, the weight that you will get when you place the cylinder on the scale will be the combined weight of the cylinder and its contents. To find the weight of the contents alone, you therefore have to subtract the weight of the empty cylinder. And to calculate density you need to know both the weight and the volume.
Lactometerlactometer
On the top
On the top
Two common pieces of equipment used to find density are a balance and a graduated cylinder. The balance is used to measure the mass of the object, while the graduated cylinder is used to measure the volume of the object. By dividing the mass by the volume, you can determine the density of the object.