answersLogoWhite

0

100MHz

Wavelength(m) is inversely proportional to frequency (Hz)

Use the equation λ=v/f (Wavelength=velocity/frequency)

For the velocity just use the value 1 as since both waves will be through the same medium it doesn't matter

0.000001m = 1ms-1 / 10,000,000Hz

0.0000001m = 1ms-1 / 100,000,000Hz

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

Which frequencies would have shortest wavelength 10mhz 100mhz 1ghz 100ghz?

The frequency with the shortest wavelength would be 100 GHz. Wavelength is inversely proportional to frequency, meaning higher frequencies have shorter wavelengths. So, 100 GHz would have a shorter wavelength compared to 1 GHz, 100 MHz, and 10 MHz.


A wave with what frequencies would have shortest wavelength 10MHz 100MHz 1GHz 100GHz?

For the same speed of a wave (I suppose you are referring to electromagnetic waves), the highest frequency corresponds to the shortest wavelength.For the same speed of a wave (I suppose you are referring to electromagnetic waves), the highest frequency corresponds to the shortest wavelength.For the same speed of a wave (I suppose you are referring to electromagnetic waves), the highest frequency corresponds to the shortest wavelength.For the same speed of a wave (I suppose you are referring to electromagnetic waves), the highest frequency corresponds to the shortest wavelength.


How long in meters is a typical radio wave with a frequency of 88 megahertz?

The length of a wave is denoted by its wavelength, which is found by dividing the speed of light, or c, (3 x 108 m/s) by the frequency (88 x 106 Hz). The answer is 3.4 meters.


Difference between channel and bandwidth?

a channel is actually a path through which a signal of a particular frequency travels and bandwidth is the capacity of that path it tells about the number or range of frequencies which a path can carry


How much bandwidth is required to send 132 voice grade channels by FDM on an international satellite system?

10MHz


What is the speed of 8086 microprocessor?

MAximum clock frequency of 8086 is 5MHZ.


How much bandwidth is required to send 132 voice-grade channels by FDM on an international satellite system?

Answer:- 500MHz From:- Joginder Kumar Network Engineer Datacraft India Ltd.


What is the difference between Atmel microprocessor Atmega88-20pu vs Atmega88pv-10pu?

20PU = 20mhz clock 10PU = 10mhz clock note that these are the maximum clock speeds. voltage and settings will apply also. I believe most AVR's default to 1mhz until you have set the specified fuse setting.


What is a wavelength region in which electromagnetic energy comes through the atmosphere easily?

Almost the whole of the E-M spectrum is easily transmitted through the atmosphere, apart from a band of frequencies from about 1.5 MHz to 10MHz . This narrow band will be interfered with by the ionized layers high in the atmosphere. The characteristics of this band depend on the nature of the Solar Wind, and upon disturbances of the Earth's magnetic field. Infrasonic E-M radiation at the low frequency end will travel through easily, as will microwave frequencies. And continuing on to light, and cosmic rays at the highest end of the frequency spectrum.


What is XT?

It's a VERY vague distinction - but HS (High Speed) gives more drive to the crystal. There's no specific changeover point - but 4MHz would be XT, and 20MHz would be HS. Often either will work, but perhaps a reasonable changeover would be 10MHz?, or even 4MHz and below is XT, and anything higher is HS?. hope this will help


How long is 1 radio wave?

Waves longer than 1mm are considered to be in the radio spectrum, submarine communications use waves kilometers long. Some radio waves are too long to be used in communications today. There are some very good answers regarding radio and TV communication in Related Answers right here on WikiAnswers.


What is XT oscillator?

It's a VERY vague distinction - but HS (High Speed) gives more drive to the crystal. There's no specific changeover point - but 4MHz would be XT, and 20MHz would be HS. Often either will work, but perhaps a reasonable changeover would be 10MHz?, or even 4MHz and below is XT, and anything higher is HS?. hope this will help