0
What else can I help you with?
How is radiator secured in on bracket?
The radiator is typically secured onto brackets using mounting hardware such as screws or bolts. The brackets are positioned on the sides of the radiator where they line up with holes in the radiator frame. By attaching the brackets securely to the radiator frame, the radiator is held in place and mounted properly.
How do you fix a half cold steam radiator?
Check to make sure the air vent on the radiator is not blocked or malfunctioning. You can try bleeding the radiator to release any air trapped inside. If that doesn't work, you may need to balance the system by adjusting the valves on the radiators throughout the building.
How does one flush a radiator?
To flush a radiator, first make sure the engine is off and cool. Locate the radiator drain plug, usually at the bottom, and use a container to catch the old coolant. Pour radiator flush solution and water into the radiator, run the engine for a few minutes, then drain the radiator by opening the drain plug. Finally, refill the radiator with the recommended coolant and water mixture.
Why a reducing orifice in the steam supply line of such an evaporator?
A reducing orifice in the steam supply line of an evaporator is used to control the flow rate of steam entering the evaporator. This helps in maintaining the desired operating conditions and ensuring efficient heat transfer within the evaporator. Additionally, it can help prevent overheating and equipment damage by limiting the amount of steam entering the system.
Why doesn't the radiator pull the water back from the reservoir even if the radiator cap is new?
If the radiator is not pulling water from the reservoir even with a new cap, there may be an issue with the radiator itself such as a clog, a faulty radiator inlet/outlet, or a malfunctioning water pump. It is recommended to have the radiator system inspected by a professional to diagnose and resolve the problem.
How do I identify the Supply and Return lines on a 3.5L Oldsmobile Intrigue transmission?
Although I am not familiar with the vehicle in question specifically, generally the line that goes to the top side of the radiator is the supply, and the line from the bottom of the radiator or trans cooler is the one returning the fluid to the trans.
There is a top bottom transmission line on the radiator and a front and rear connection on the trans where does the top line from the radiator connect on the trans front or back?
upper line on radiator connects to transmission front
What is the process for toilet supply line replacement?
The process for toilet supply line replacement involves turning off the water supply, disconnecting the old supply line, installing a new supply line, and then turning the water supply back on to check for leaks.
What is line in line regulation?
Line refers to the a.c. supply line. Line regulation is the change in output of a device, usually a power supply, which is due to variations in the voltage of the a.c. supply.
what line is the return line for the water to radiator?
The top hose.
Where is bottom radiator line of 1985 Mercedes 500 SEL?
Bottom of the radiator
Where is the thermostat on a 1993 Oldsmobile cutlass ciera s located?
The 1993 Oldsmobile Cutlass Sierra thermostat is located on the front of the engine. You can follow the water supply line from the radiator to the thermostat housing.
What is the best way to replace a toilet supply line?
To replace a toilet supply line, first turn off the water supply, disconnect the old line, and install the new line by connecting it to the toilet and water supply valve. Finally, turn the water supply back on and check for any leaks.
How long does it take to install a radiator in a 1993 Taurus wagon?
I have a 93 3.8 and it's not a bad project but the lower oil cooler line is a b..tch, disconnect the lower line from the two brackets under the radiator and install lower line before you install the radiator
How do you replace radiator water on 2003 passat wagon?
unplug line at bottom of overflow or bottom of radiator
What is the purpose of a supply line in plumbing?
supply potable water
How can I replace a toilet supply line?
To replace a toilet supply line, first turn off the water supply valve behind the toilet. Disconnect the old supply line from the valve and the toilet tank. Install the new supply line by connecting one end to the valve and the other end to the toilet tank. Turn the water supply back on and check for any leaks.
