answersLogoWhite

0

more accurate

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Physics

Which can push with great force?

A rocket engine is capable of generating a high amount of thrust or pushing force due to the rapid expulsion of high-velocity exhaust gases ejected from the engine nozzle. This force is vital for propelling rockets and spacecraft into space.


In a jet engine what is sucked into the front of a compresser where what is injected into the high pressure air is injected and is pushed out of what?

In a jet engine, air is sucked into the front of the compressor where fuel is injected and mixed with the high-pressure air. This mixture is then ignited in the combustion chamber and the resulting high-temperature, high-pressure gases are pushed out of the exhaust nozzle to create thrust for propulsion.


How is thrust created by a jet engine?

Thrust in a jet engine is created by the expulsion of high-velocity exhaust gases from the engine's nozzle. This is achieved by combusting fuel with compressed air to create a high-pressure and high-temperature gas flow. The reaction force from expelling this gas flow in one direction propels the aircraft forward in the opposite direction.


What is the value of 350 kgf in newton meter?

I interpret " kgf " to mean "kilogram-foot". As such, it's a bogus unit that I'm pretty certain would never be encountered, since it mixes two different systems of units, and uses a unit of mass in place of a unit of force. But then, if the question made sense, then anyone could answer it. It is only nonsense questions like this one that require the 'Special High-Intensity Talent'® available here on WikiAnswers. In place of 'kg', we'll substitute its weight on Earth in Newtons ... 9.8 . 1 kgf = (9.8 newton-foot) (meter/3.28084 ft) = 2.987 newton-meter


How do homogenizers work?

Homogenizers work by forcing a liquid under high pressure through a small orifice or valve. This process breaks down the particles in the liquid to create a more uniform and stable mixture. The high velocity shear forces generated by the homogenizer help reduce particle size and create a consistent product.

Related Questions

What are the best maintenance tips for a high pressure washer nozzle?

To maintain a high pressure washer nozzle, regularly clean it with water and a soft brush to remove debris. Check for any clogs or damage, and replace the nozzle if necessary. Store the nozzle in a dry place when not in use to prevent corrosion.


Where is the orifice tube on a 1999 Chevrolet Suburban?

Most orifice tubes are placed in the high pressure line to the evaporator at the fire wall connection. You will have to empty the freon from the system to replace the orifice tube which is not very expensive (the tube, that is).


If a parking meter were a meter high how many inches high would it be?

A meter is equal to approximately 39.37 inches. Therefore, a parking meter that is one meter high would be approximately 39.37 inches high.


Where is the orifice filter located on a 98 escort zx2?

in the high pressure line


What is ment by high resistance and low resistance on a meter?

On a multimeter, a high resistance would indicate a high Ohmic value and a low resistance would indicate a low Ohmic value. Specific values would be relative to device you are measuring.


What causes high pressure on low side if no refrigerant added on a 1999 cadillac?

sounds like there is no orifice tube in it. orifice tube should be located just before it enters the firewall at end of high pressure line


How do you do high jumps on Super Mario Sunshine?

You must have the Rocket Nozzle for FLUDD.


What are the benefits of using a high pressure nozzle for a pressure washer?

Using a high pressure nozzle for a pressure washer provides more powerful cleaning, faster results, and better efficiency compared to lower pressure nozzles.


If a parking meter were a meter high how many inch would it be?

39.37 inches high.


Where is the orifice tube for a hummer h2?

inbetween the high and low side fittings, Evacuate the system then remove the nut and spread the lines. the small side of the orifice goes toward the evaporator(or firewall)


How high is a meter in miles?

1 meter is 0.00062137 miles.


What has the author Raymond S Castner written?

Raymond S. Castner has written: 'Design and checkout of a high speed research nozzle evaluation rig' -- subject(s): Evaluation, Design analysis, Scale models, High speed, Nozzle flow